Base structure for BLE support on ESP32-S3 boards

Bluetooth.h

@@ -14,18 +14,27 @@
 // along with this program.  If not, see <https://www.gnu.org/licenses/>.
 
 #if MCU_VARIANT == MCU_ESP32
+  
+
+#elif MCU_VARIANT == MCU_NRF52
+#endif
+
+#if MCU_VARIANT == MCU_ESP32
+  #if HAS_BLUETOOTH == true
     #include "BluetoothSerial.h"
     #include "esp_bt_main.h"
     #include "esp_bt_device.h"
+    BluetoothSerial SerialBT;
+  #elif HAS_BLE == true
+    #include "esp_bt_main.h"
+    #include "esp_bt_device.h"
+    // TODO: Remove
+    #define SerialBT Serial
+  #endif
 
 #elif MCU_VARIANT == MCU_NRF52
   #include <bluefruit.h>
   #include <math.h>
-#endif
-
-#if MCU_VARIANT == MCU_ESP32
-BluetoothSerial SerialBT;
-#elif MCU_VARIANT == MCU_NRF52
   BLEUart SerialBT;
   BLEDis  bledis;
   BLEBas  blebas;
@@ -42,6 +51,7 @@ char bt_dh[BT_DEV_HASH_LEN];
 char bt_devname[11];
 
 #if MCU_VARIANT == MCU_ESP32
+  #if HAS_BLUETOOTH == true
 
     void bt_confirm_pairing(uint32_t numVal) {
       bt_ssp_pin = numVal;
@@ -151,6 +161,92 @@ char bt_devname[11];
       }
     }
 
+  #elif HAS_BLE == true
+    void bt_stop() {
+      if (bt_state != BT_STATE_OFF) {
+        bt_allow_pairing = false;
+        bt_state = BT_STATE_OFF;
+      }
+    }
+
+    void bt_disable_pairing() {
+      bt_allow_pairing = false;
+      bt_ssp_pin = 0;
+      bt_state = BT_STATE_ON;
+    }
+
+    void bt_connect_callback(uint16_t conn_handle) {
+      bt_state = BT_STATE_CONNECTED;
+      cable_state = CABLE_STATE_DISCONNECTED;
+    }
+
+    void bt_disconnect_callback(uint16_t conn_handle, uint8_t reason) {
+      bt_state = BT_STATE_ON;
+    }
+
+    bool bt_setup_hw() {
+      if (!bt_ready) {
+        if (EEPROM.read(eeprom_addr(ADDR_CONF_BT)) == BT_ENABLE_BYTE) {
+          bt_enabled = true;
+        } else {
+          bt_enabled = false;
+        }
+        if (btStart()) {
+          if (esp_bluedroid_init() == ESP_OK) {
+            if (esp_bluedroid_enable() == ESP_OK) {
+              const uint8_t* bda_ptr = esp_bt_dev_get_address();
+              char *data = (char*)malloc(BT_DEV_ADDR_LEN+1);
+              for (int i = 0; i < BT_DEV_ADDR_LEN; i++) {
+                  data[i] = bda_ptr[i];
+              }
+              data[BT_DEV_ADDR_LEN] = EEPROM.read(eeprom_addr(ADDR_SIGNATURE));
+              unsigned char *hash = MD5::make_hash(data, BT_DEV_ADDR_LEN);
+              memcpy(bt_dh, hash, BT_DEV_HASH_LEN);
+              sprintf(bt_devname, "RNode %02X%02X", bt_dh[14], bt_dh[15]);
+              free(data);
+
+              // TODO: Implement GAP & GATT for RNode comms over BLE
+              
+              bt_ready = true;
+              return true;
+
+            } else { return false; }
+          } else { return false; }
+        } else { return false; }
+      } else { return false; }
+    }
+
+    void bt_start() {
+      if (bt_state == BT_STATE_OFF) {
+        bt_state = BT_STATE_ON;
+        // TODO: Implement
+      }
+    }
+
+    bool bt_init() {
+        bt_state = BT_STATE_OFF;
+        if (bt_setup_hw()) {
+          if (bt_enabled && !console_active) bt_start();
+          return true;
+        } else {
+          return false;
+        }
+    }
+
+    void bt_enable_pairing() {
+      if (bt_state == BT_STATE_OFF) bt_start();
+      bt_allow_pairing = true;
+      bt_pairing_started = millis();
+      bt_state = BT_STATE_PAIRING;
+    }
+
+    void update_bt() {
+      if (bt_allow_pairing && millis()-bt_pairing_started >= BT_PAIRING_TIMEOUT) {
+        bt_disable_pairing();
+      }
+    }
+  #endif
+
 #elif MCU_VARIANT == MCU_NRF52
 uint8_t eeprom_read(uint32_t mapped_addr);
 
@@ -244,8 +340,8 @@ bool bt_setup_hw() {
 void bt_start() {
   if (bt_state == BT_STATE_OFF) {
     Bluefruit.setName(bt_devname);
-    bledis.setManufacturer("Adafruit Industries");
+    bledis.setManufacturer(BLE_MANUFACTURER);
-    bledis.setModel("Bluefruit Feather52");
+    bledis.setModel(BLE_MODEL);
     // start device information service
     bledis.begin();
 

Boards.h

@@ -252,14 +252,11 @@
     #elif BOARD_MODEL == BOARD_HELTEC32_V3
       #define IS_ESP32S3 true
       #define HAS_DISPLAY true
-      //ESP32-S3 no bluetooth classic
       #define HAS_BLUETOOTH false
-      // TODO BLE
+      #define HAS_BLE true
-      #define HAS_BLE false
       // Cannot run wifi and BLE at same time?
       #define HAS_CONSOLE false
       #define HAS_EEPROM true
-      // Only one LED on pin 35
       #if defined(EXTERNAL_LEDS)
         const int pin_led_rx = 13;
         const int pin_led_tx = 14;
@@ -283,8 +280,6 @@
       const int pin_miso = 11;
       const int pin_sclk = 9;
 
-
-
     #elif BOARD_MODEL == BOARD_RNODE_NG_20
       #define HAS_DISPLAY true
       #define HAS_BLUETOOTH true
@@ -341,9 +336,9 @@
       #define HAS_TCXO true
 
       #define HAS_DISPLAY true
+      #define HAS_CONSOLE false
+      #define HAS_BLUETOOTH false
       #define HAS_BLE true
-      #define HAS_BLUETOOTH false // TODO: Implement
-      #define HAS_CONSOLE false   // TODO: Implement
       #define HAS_PMU true
       #define HAS_NP false
       #define HAS_SD false
@@ -384,8 +379,9 @@
   #elif MCU_VARIANT == MCU_NRF52
     #if BOARD_MODEL == BOARD_RAK4630
       #define HAS_EEPROM false
-      #define HAS_DISPLAY false // set for debugging
+      #define HAS_DISPLAY true
-      #define HAS_BLUETOOTH true
+      #define HAS_BLUETOOTH false
+      #define HAS_BLE true
       #define HAS_CONSOLE false
       #define HAS_PMU false
       #define HAS_NP false
@@ -398,8 +394,10 @@
       #define CONFIG_QUEUE_MAX_LENGTH 200
       #define EEPROM_SIZE 200
       #define EEPROM_OFFSET EEPROM_SIZE-EEPROM_RESERVED
+      #define BLE_MANUFACTURER "RAK Wireless"
+      #define BLE_MODEL "RAK4640"
 
-      // following pins are for the sx1262
+      // Following pins are for the sx1262
       const int pin_rxen = 37;
       const int pin_reset = 38;
       const int pin_cs = 42;

Device.h

@@ -154,7 +154,7 @@ bool device_init() {
     mbedtls_md_init(&ctx);
     mbedtls_md_setup(&ctx, mbedtls_md_info_from_type(md_type), 0);
     mbedtls_md_starts(&ctx);
-    #if HAS_BLUETOOTH == true
+    #if HAS_BLUETOOTH == true || HAS_BLE == true
       mbedtls_md_update(&ctx, dev_bt_mac, BT_DEV_ADDR_LEN);
     #else
       // TODO: Get from BLE stack instead

RNode_Firmware.ino

@@ -33,7 +33,7 @@ volatile uint16_t queued_bytes = 0;
 volatile uint16_t queue_cursor = 0;
 volatile uint16_t current_packet_start = 0;
 volatile bool serial_buffering = false;
-#if HAS_BLUETOOTH
+#if HAS_BLUETOOTH || HAS_BLE == true
   bool bt_init_ran = false;
 #endif
 
@@ -160,12 +160,9 @@ void setup() {
       pmu_ready = init_pmu();
     #endif
 
-    #if HAS_BLUETOOTH
+    #if HAS_BLUETOOTH || HAS_BLE == true
       bt_init();
       bt_init_ran = true;
-    #elif HAS_BLE
-      // TODO: Implement BLE on ESP32S3 instead of this hack
-      bt_ready = true;
     #endif
 
     if (console_active) {
@@ -910,7 +907,7 @@ void serialCallback(uint8_t sbyte) {
           }
       #endif
     } else if (command == CMD_BT_CTRL) {
-      #if HAS_BLUETOOTH
+      #if HAS_BLUETOOTH || HAS_BLE
         if (sbyte == 0x00) {
           bt_stop();
           bt_conf_save(false);
@@ -1111,15 +1108,7 @@ void validate_status() {
               if (device_init()) {
                 hw_ready = true;
               } else {
-                #if !HAS_BLUETOOTH && !HAS_BLE
-                  // Without bluetooth, bt_ready and device_init_done 
-                  // are not set
-                  // and neither is hw_ready (see device_init())
-                  hw_ready = true;
-                  device_init_done = true;
-                #else
                 hw_ready = false;
-                #endif
               }
             #else
               hw_ready = true;
@@ -1297,7 +1286,7 @@ void loop() {
     if (pmu_ready) update_pmu();
   #endif
 
-  #if HAS_BLUETOOTH
+  #if HAS_BLUETOOTH || HAS_BLE == true
     if (!console_active && bt_ready) update_bt();
   #endif
 }
@@ -1329,7 +1318,7 @@ void buffer_serial() {
 
     uint8_t c = 0;
 
-    #if HAS_BLUETOOTH
+    #if HAS_BLUETOOTH || HAS_BLE == true
     while (
       c < MAX_CYCLES &&
       ( (bt_state != BT_STATE_CONNECTED && Serial.available()) || (bt_state == BT_STATE_CONNECTED && SerialBT.available()) )
@@ -1344,7 +1333,7 @@ void buffer_serial() {
         if (!fifo_isfull_locked(&serialFIFO)) {
           fifo_push_locked(&serialFIFO, Serial.read());
         }
-      #elif HAS_BLUETOOTH
+      #elif HAS_BLUETOOTH || HAS_BLE == true
         if (bt_state == BT_STATE_CONNECTED) {
           if (!fifo_isfull(&serialFIFO)) {
             fifo_push(&serialFIFO, SerialBT.read());

Utilities.h

@@ -47,7 +47,7 @@ sx128x *LoRa = &sx128x_modem;
   #include "Display.h"
 #endif
 
-#if HAS_BLUETOOTH == true
+#if HAS_BLUETOOTH == true || HAS_BLE == true
 	void kiss_indicate_btpin();
   #include "Bluetooth.h"
 #endif
@@ -629,7 +629,7 @@ int8_t  led_standby_direction = 0;
 #endif
 
 void serial_write(uint8_t byte) {
-	#if HAS_BLUETOOTH
+	#if HAS_BLUETOOTH || HAS_BLE == true
 		if (bt_state != BT_STATE_CONNECTED) {
 			Serial.write(byte);
 		} else {
@@ -829,7 +829,7 @@ void kiss_indicate_battery() {
 }
 
 void kiss_indicate_btpin() {
-	#if HAS_BLUETOOTH
+	#if HAS_BLUETOOTH || HAS_BLE == true
 		serial_write(FEND);
 		serial_write(CMD_BT_PIN);
 		escaped_serial_write(bt_ssp_pin>>24);