arduino-esp32/cores/esp32/esp32-hal-touch.c

173 lines
6.6 KiB
C
Raw Normal View History

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#include "esp32-hal-touch.h"
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "rom/ets_sys.h"
#include "esp_attr.h"
#include "esp_intr.h"
#include "soc/rtc_io_reg.h"
#include "soc/rtc_cntl_reg.h"
#include "soc/sens_reg.h"
#define RTC_TOUCH_INUM 13
static uint16_t __touchSleepCycles = 0x1000;
static uint16_t __touchMeasureCycles = 0x1000;
typedef void (*voidFuncPtr)(void);
static voidFuncPtr __touchInterruptHandlers[10] = {0,};
void IRAM_ATTR __touchISR(void * arg)
{
uint32_t pad_intr = READ_PERI_REG(SENS_SAR_TOUCH_CTRL2_REG) & 0x3ff;
uint32_t rtc_intr = READ_PERI_REG(RTC_CNTL_INT_ST_REG);
uint8_t i = 0;
//clear interrupt
WRITE_PERI_REG(RTC_CNTL_INT_CLR_REG, rtc_intr);
SET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_MEAS_EN_CLR);
if (rtc_intr & RTC_CNTL_TOUCH_INT_ST) {
for (i = 0; i < 10; ++i) {
if ((pad_intr >> i) & 0x01) {
if(__touchInterruptHandlers[i]){
__touchInterruptHandlers[i]();
}
}
}
}
}
void __touchSetCycles(uint16_t measure, uint16_t sleep)
{
__touchSleepCycles = sleep;
__touchMeasureCycles = measure;
//Touch pad SleepCycle Time
SET_PERI_REG_BITS(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_SLEEP_CYCLES, __touchSleepCycles, SENS_TOUCH_SLEEP_CYCLES_S);
//Touch Pad Measure Time
SET_PERI_REG_BITS(SENS_SAR_TOUCH_CTRL1_REG, SENS_TOUCH_MEAS_DELAY, __touchMeasureCycles, SENS_TOUCH_MEAS_DELAY_S);
}
void __touchInit()
{
static bool initialized = false;
if(initialized){
return;
}
SET_PERI_REG_BITS(RTC_IO_TOUCH_CFG_REG, RTC_IO_TOUCH_XPD_BIAS, 1, RTC_IO_TOUCH_XPD_BIAS_S);
SET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_MEAS_EN_CLR);
//clear touch enable
WRITE_PERI_REG(SENS_SAR_TOUCH_ENABLE_REG, 0x0);
SET_PERI_REG_MASK(RTC_CNTL_STATE0_REG, RTC_CNTL_TOUCH_SLP_TIMER_EN);
__touchSetCycles(__touchMeasureCycles, __touchSleepCycles);
ESP_INTR_DISABLE(RTC_TOUCH_INUM);
intr_matrix_set(xPortGetCoreID(), ETS_RTC_CORE_INTR_SOURCE, RTC_TOUCH_INUM);
xt_set_interrupt_handler(RTC_TOUCH_INUM, &__touchISR, NULL);
ESP_INTR_ENABLE(RTC_TOUCH_INUM);
initialized = true;
}
uint16_t __touchRead(uint8_t pin)
{
int8_t pad = digitalPinToTouchChannel(pin);
if(pad < 0){
return 0;
}
pinMode(pin, ANALOG);
__touchInit();
uint32_t v0 = READ_PERI_REG(SENS_SAR_TOUCH_ENABLE_REG);
//Disable Intr & enable touch pad
WRITE_PERI_REG(SENS_SAR_TOUCH_ENABLE_REG,
(v0 & ~((1 << (pad + SENS_TOUCH_PAD_OUTEN2_S)) | (1 << (pad + SENS_TOUCH_PAD_OUTEN1_S))))
| (1 << (pad + SENS_TOUCH_PAD_WORKEN_S)));
SET_PERI_REG_MASK(SENS_SAR_TOUCH_ENABLE_REG, (1 << (pad + SENS_TOUCH_PAD_WORKEN_S)));
uint32_t rtc_tio_reg = RTC_IO_TOUCH_PAD0_REG + pad * 4;
WRITE_PERI_REG(rtc_tio_reg, (READ_PERI_REG(rtc_tio_reg)
& ~(RTC_IO_TOUCH_PAD0_DAC_M))
| (7 << RTC_IO_TOUCH_PAD0_DAC_S)//Touch Set Slope
| RTC_IO_TOUCH_PAD0_TIE_OPT_M //Enable Tie,Init Level
| RTC_IO_TOUCH_PAD0_START_M //Enable Touch Pad IO
| RTC_IO_TOUCH_PAD0_XPD_M); //Enable Touch Pad Power on
//force oneTime test start
SET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_START_EN_M|SENS_TOUCH_START_FORCE_M);
SET_PERI_REG_BITS(SENS_SAR_TOUCH_CTRL1_REG, SENS_TOUCH_XPD_WAIT, 10, SENS_TOUCH_XPD_WAIT_S);
while (GET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_MEAS_DONE) == 0) {};
uint16_t touch_value = READ_PERI_REG(SENS_SAR_TOUCH_OUT1_REG + (pad / 2) * 4) >> ((pad & 1) ? SENS_TOUCH_MEAS_OUT1_S : SENS_TOUCH_MEAS_OUT0_S);
//clear touch force ,select the Touch mode is Timer
CLEAR_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_START_EN_M|SENS_TOUCH_START_FORCE_M);
//restore previous value
WRITE_PERI_REG(SENS_SAR_TOUCH_ENABLE_REG, v0);
return touch_value;
}
void __touchAttachInterrupt(uint8_t pin, void (*userFunc)(void), uint16_t threshold)
{
int8_t pad = digitalPinToTouchChannel(pin);
if(pad < 0){
return;
}
pinMode(pin, ANALOG);
__touchInit();
__touchInterruptHandlers[pad] = userFunc;
//clear touch force ,select the Touch mode is Timer
CLEAR_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_START_EN_M|SENS_TOUCH_START_FORCE_M);
//interrupt when touch value < threshold
CLEAR_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL1_REG, SENS_TOUCH_OUT_SEL);
//Intr will give ,when SET0 < threshold
SET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL1_REG, SENS_TOUCH_OUT_1EN);
//Enable Rtc Touch Module Intr,the Interrupt need Rtc out Enable
SET_PERI_REG_MASK(RTC_CNTL_INT_ENA_REG, RTC_CNTL_TOUCH_INT_ENA);
//set threshold
uint8_t shift = (pad & 1) ? SENS_TOUCH_OUT_TH1_S : SENS_TOUCH_OUT_TH0_S;
SET_PERI_REG_BITS((SENS_SAR_TOUCH_THRES1_REG + (pad / 2) * 4), SENS_TOUCH_OUT_TH0, threshold, shift);
uint32_t rtc_tio_reg = RTC_IO_TOUCH_PAD0_REG + pad * 4;
WRITE_PERI_REG(rtc_tio_reg, (READ_PERI_REG(rtc_tio_reg)
& ~(RTC_IO_TOUCH_PAD0_DAC_M))
| (7 << RTC_IO_TOUCH_PAD0_DAC_S)//Touch Set Slope
| RTC_IO_TOUCH_PAD0_TIE_OPT_M //Enable Tie,Init Level
| RTC_IO_TOUCH_PAD0_START_M //Enable Touch Pad IO
| RTC_IO_TOUCH_PAD0_XPD_M); //Enable Touch Pad Power on
//Enable Digital rtc control :work mode and out mode
SET_PERI_REG_MASK(SENS_SAR_TOUCH_ENABLE_REG,
(1 << (pad + SENS_TOUCH_PAD_WORKEN_S)) | \
(1 << (pad + SENS_TOUCH_PAD_OUTEN2_S)) | \
(1 << (pad + SENS_TOUCH_PAD_OUTEN1_S)));
}
extern uint16_t touchRead(uint8_t pin) __attribute__ ((weak, alias("__touchRead")));
extern void touchAttachInterrupt(uint8_t pin, void (*userFunc)(void), uint16_t threshold) __attribute__ ((weak, alias("__touchAttachInterrupt")));
extern void touchSetCycles(uint16_t measure, uint16_t sleep) __attribute__ ((weak, alias("__touchSetCycles")));