/*
   BLE5 extended scan example for esp32 C3 and S3
   with this code it is simple to scan legacy (BLE4) compatible advertising,
   and BLE5 extended advertising. New coded added in BLEScan is not changing old behavior,
   which can be used with old esp32, but is adding functionality to use on C3/S3.
   With this new API advertised device wont be stored in API, it is now user responsibility

   author: chegewara
*/
#ifndef CONFIG_BT_BLE_50_FEATURES_SUPPORTED
#warning "Not compatible hardware"
#else
#include <BLEDevice.h>
#include <BLEUtils.h>
#include <BLEScan.h>
#include <BLEAdvertisedDevice.h>

uint32_t scanTime = 100; //In 10ms (1000ms)
BLEScan* pBLEScan;

/**
* @brief extend adv report parameters
*/
//typedef struct {
//    esp_ble_gap_adv_type_t event_type;              /*!< extend advertising type */
//    uint8_t addr_type;                              /*!< extend advertising address type */
//    esp_bd_addr_t addr;                             /*!< extend advertising address */
//    esp_ble_gap_pri_phy_t primary_phy;              /*!< extend advertising primary phy */
//    esp_ble_gap_phy_t secondly_phy;                 /*!< extend advertising secondary phy */
//    uint8_t sid;                                    /*!< extend advertising sid */
//    uint8_t tx_power;                               /*!< extend advertising tx power */
//    int8_t rssi;                                    /*!< extend advertising rssi */
//    uint16_t per_adv_interval;                      /*!< periodic advertising interval */
//    uint8_t dir_addr_type;                          /*!< direct address type */
//    esp_bd_addr_t dir_addr;                         /*!< direct address */
//    esp_ble_gap_ext_adv_data_status_t data_status;  /*!< data type */
//    uint8_t adv_data_len;                           /*!< extend advertising data length */
//    uint8_t adv_data[251];                          /*!< extend advertising data */
//} esp_ble_gap_ext_adv_reprot_t;

class MyBLEExtAdvertisingCallbacks: public BLEExtAdvertisingCallbacks {
    void onResult(esp_ble_gap_ext_adv_reprot_t report) {
      if(report.event_type & ESP_BLE_GAP_SET_EXT_ADV_PROP_LEGACY){
        // here we can receive regular advertising data from BLE4.x devices
        Serial.println("BLE4.2");
      } else {
        // here we will get extended advertising data that are advertised over data channel by BLE5 divices
        Serial.printf("Ext advertise: data_le: %d, data_status: %d \n", report.adv_data_len, report.data_status);
      }
    }
};

void setup() {
  Serial.begin(115200);
  Serial.println("Scanning...");

  BLEDevice::init("");
  pBLEScan = BLEDevice::getScan(); //create new scan
  pBLEScan->setExtendedScanCallback(new MyBLEExtAdvertisingCallbacks());
  pBLEScan->setExtScanParams(); // use with pre-defined/default values, overloaded function allows to pass parameters
  delay(1000); // it is just for simplicity this example, to let ble stack to set extended scan params
  pBLEScan->startExtScan(scanTime, 3); // scan duration in n * 10ms, period - repeat after n seconds (period >= duration)
}

void loop() {
  // put your main code here, to run repeatedly:
  delay(2000);
}
#endif // CONFIG_BT_BLE_50_FEATURES_SUPPORTED