// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD // // Licensed under the Apache License, Version 2.0 (the "License"); // you may not use this file except in compliance with the License. // You may obtain a copy of the License at // // http://www.apache.org/licenses/LICENSE-2.0 // // Unless required by applicable law or agreed to in writing, software // distributed under the License is distributed on an "AS IS" BASIS, // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. // See the License for the specific language governing permissions and // limitations under the License. #ifndef _SOC_SDMMC_STRUCT_H_ #define _SOC_SDMMC_STRUCT_H_ #include #include #ifdef __cplusplus extern "C" { #endif typedef struct { uint32_t reserved1: 1; uint32_t disable_int_on_completion: 1; uint32_t last_descriptor: 1; uint32_t first_descriptor: 1; uint32_t second_address_chained: 1; uint32_t end_of_ring: 1; uint32_t reserved2: 24; uint32_t card_error_summary: 1; uint32_t owned_by_idmac: 1; uint32_t buffer1_size: 13; uint32_t buffer2_size: 13; uint32_t reserved3: 6; void* buffer1_ptr; union { void* buffer2_ptr; void* next_desc_ptr; }; } sdmmc_desc_t; #define SDMMC_DMA_MAX_BUF_LEN 4096 _Static_assert(sizeof(sdmmc_desc_t) == 16, "invalid size of sdmmc_desc_t structure"); typedef struct { uint32_t cmd_index: 6; ///< Command index uint32_t response_expect: 1; ///< set if response is expected uint32_t response_long: 1; ///< 0: short response expected, 1: long response expected uint32_t check_response_crc: 1; ///< set if controller should check response CRC uint32_t data_expected: 1; ///< 0: no data expected, 1: data expected uint32_t rw: 1; ///< 0: read from card, 1: write to card (don't care if no data expected) uint32_t stream_mode: 1; ///< 0: block transfer, 1: stream transfer (don't care if no data expected) uint32_t send_auto_stop: 1; ///< set to send stop at the end of the transfer uint32_t wait_complete: 1; ///< 0: send command at once, 1: wait for previous command to complete uint32_t stop_abort_cmd: 1; ///< set if this is a stop or abort command intended to stop current transfer uint32_t send_init: 1; ///< set to send init sequence (80 clocks of 1) uint32_t card_num: 5; ///< card number uint32_t update_clk_reg: 1; ///< 0: normal command, 1: don't send command, just update clock registers uint32_t read_ceata: 1; ///< set if performing read from CE-ATA device uint32_t ccs_expected: 1; ///< set if CCS is expected from CE-ATA device uint32_t enable_boot: 1; ///< set for mandatory boot mode uint32_t expect_boot_ack: 1; ///< when set along with enable_boot, controller expects boot ack pattern uint32_t disable_boot: 1; ///< set to terminate boot operation (don't set along with enable_boot) uint32_t boot_mode: 1; ///< 0: mandatory boot operation, 1: alternate boot operation uint32_t volt_switch: 1; ///< set to enable voltage switching (for CMD11 only) uint32_t use_hold_reg: 1; ///< clear to bypass HOLD register uint32_t reserved: 1; uint32_t start_command: 1; ///< Start command; once command is sent to the card, bit is cleared. } sdmmc_hw_cmd_t; ///< command format used in cmd register; this structure is defined to make it easier to build command values _Static_assert(sizeof(sdmmc_hw_cmd_t) == 4, "invalid size of sdmmc_cmd_t structure"); typedef volatile struct { union { struct { uint32_t controller_reset: 1; uint32_t fifo_reset: 1; uint32_t dma_reset: 1; uint32_t reserved1: 1; uint32_t int_enable: 1; uint32_t dma_enable: 1; uint32_t read_wait: 1; uint32_t send_irq_response: 1; uint32_t abort_read_data: 1; uint32_t send_ccsd: 1; uint32_t send_auto_stop_ccsd: 1; uint32_t ceata_device_interrupt_status: 1; uint32_t reserved2: 4; uint32_t card_voltage_a: 4; uint32_t card_voltage_b: 4; uint32_t enable_od_pullup: 1; uint32_t use_internal_dma: 1; uint32_t reserved3: 6; }; uint32_t val; } ctrl; uint32_t pwren; ///< 1: enable power to card, 0: disable power to card union { struct { uint32_t div0: 8; ///< 0: bypass, 1-255: divide clock by (2*div0). uint32_t div1: 8; ///< 0: bypass, 1-255: divide clock by (2*div0). uint32_t div2: 8; ///< 0: bypass, 1-255: divide clock by (2*div0). uint32_t div3: 8; ///< 0: bypass, 1-255: divide clock by (2*div0). }; uint32_t val; } clkdiv; union { struct { uint32_t card0: 2; ///< 0-3: select clock divider for card 0 among div0-div3 uint32_t card1: 2; ///< 0-3: select clock divider for card 1 among div0-div3 uint32_t reserved: 28; }; uint32_t val; } clksrc; union { struct { uint32_t cclk_enable: 16; ///< 1: enable clock to card, 0: disable clock uint32_t cclk_low_power: 16; ///< 1: enable clock gating when card is idle, 0: disable clock gating }; uint32_t val; } clkena; union { struct { uint32_t response: 8; ///< response timeout, in card output clock cycles uint32_t data: 24; ///< data read timeout, in card output clock cycles }; uint32_t val; } tmout; union { struct { uint32_t card_width: 16; ///< one bit for each card: 0: 1-bit mode, 1: 4-bit mode uint32_t card_width_8: 16; ///< one bit for each card: 0: not 8-bit mode (corresponding card_width bit is used), 1: 8-bit mode (card_width bit is ignored) }; uint32_t val; } ctype; uint32_t blksiz: 16; ///< block size, default 0x200 uint32_t : 16; uint32_t bytcnt; ///< number of bytes to be transferred union { struct { uint32_t cd: 1; ///< Card detect interrupt enable uint32_t re: 1; ///< Response error interrupt enable uint32_t cmd_done: 1; ///< Command done interrupt enable uint32_t dto: 1; ///< Data transfer over interrupt enable uint32_t txdr: 1; ///< Transmit FIFO data request interrupt enable uint32_t rxdr: 1; ///< Receive FIFO data request interrupt enable uint32_t rcrc: 1; ///< Response CRC error interrupt enable uint32_t dcrc: 1; ///< Data CRC error interrupt enable uint32_t rto: 1; ///< Response timeout interrupt enable uint32_t drto: 1; ///< Data read timeout interrupt enable uint32_t hto: 1; ///< Data starvation-by-host timeout interrupt enable uint32_t frun: 1; ///< FIFO underrun/overrun error interrupt enable uint32_t hle: 1; ///< Hardware locked write error interrupt enable uint32_t sbi_bci: 1; ///< Start bit error / busy clear interrupt enable uint32_t acd: 1; ///< Auto command done interrupt enable uint32_t ebe: 1; ///< End bit error / write no CRC interrupt enable uint32_t sdio: 16; ///< SDIO interrupt enable }; uint32_t val; } intmask; uint32_t cmdarg; ///< Command argument to be passed to card sdmmc_hw_cmd_t cmd; uint32_t resp[4]; ///< Response from card union { struct { uint32_t cd: 1; ///< Card detect interrupt masked status uint32_t re: 1; ///< Response error interrupt masked status uint32_t cmd_done: 1; ///< Command done interrupt masked status uint32_t dto: 1; ///< Data transfer over interrupt masked status uint32_t txdr: 1; ///< Transmit FIFO data request interrupt masked status uint32_t rxdr: 1; ///< Receive FIFO data request interrupt masked status uint32_t rcrc: 1; ///< Response CRC error interrupt masked status uint32_t dcrc: 1; ///< Data CRC error interrupt masked status uint32_t rto: 1; ///< Response timeout interrupt masked status uint32_t drto: 1; ///< Data read timeout interrupt masked status uint32_t hto: 1; ///< Data starvation-by-host timeout interrupt masked status uint32_t frun: 1; ///< FIFO underrun/overrun error interrupt masked status uint32_t hle: 1; ///< Hardware locked write error interrupt masked status uint32_t sbi_bci: 1; ///< Start bit error / busy clear interrupt masked status uint32_t acd: 1; ///< Auto command done interrupt masked status uint32_t ebe: 1; ///< End bit error / write no CRC interrupt masked status uint32_t sdio: 16; ///< SDIO interrupt masked status }; uint32_t val; } mintsts; union { struct { uint32_t cd: 1; ///< Card detect raw interrupt status uint32_t re: 1; ///< Response error raw interrupt status uint32_t cmd_done: 1; ///< Command done raw interrupt status uint32_t dto: 1; ///< Data transfer over raw interrupt status uint32_t txdr: 1; ///< Transmit FIFO data request raw interrupt status uint32_t rxdr: 1; ///< Receive FIFO data request raw interrupt status uint32_t rcrc: 1; ///< Response CRC error raw interrupt status uint32_t dcrc: 1; ///< Data CRC error raw interrupt status uint32_t rto: 1; ///< Response timeout raw interrupt status uint32_t drto: 1; ///< Data read timeout raw interrupt status uint32_t hto: 1; ///< Data starvation-by-host timeout raw interrupt status uint32_t frun: 1; ///< FIFO underrun/overrun error raw interrupt status uint32_t hle: 1; ///< Hardware locked write error raw interrupt status uint32_t sbi_bci: 1; ///< Start bit error / busy clear raw interrupt status uint32_t acd: 1; ///< Auto command done raw interrupt status uint32_t ebe: 1; ///< End bit error / write no CRC raw interrupt status uint32_t sdio: 16; ///< SDIO raw interrupt status }; uint32_t val; } rintsts; ///< interrupts can be cleared by writing this register union { struct { uint32_t fifo_rx_watermark: 1; ///< FIFO reached receive watermark level uint32_t fifo_tx_watermark: 1; ///< FIFO reached transmit watermark level uint32_t fifo_empty: 1; ///< FIFO is empty uint32_t fifo_full: 1; ///< FIFO is full uint32_t cmd_fsm_state: 4; ///< command FSM state uint32_t data3_status: 1; ///< this bit reads 1 if card is present uint32_t data_busy: 1; ///< this bit reads 1 if card is busy uint32_t data_fsm_busy: 1; ///< this bit reads 1 if transmit/receive FSM is busy uint32_t response_index: 6; ///< index of the previous response uint32_t fifo_count: 13; ///< number of filled locations in the FIFO uint32_t dma_ack: 1; ///< DMA acknowledge signal uint32_t dma_req: 1; ///< DMA request signal }; uint32_t val; } status; union { struct { uint32_t tx_watermark: 12; ///< FIFO TX watermark level uint32_t reserved1: 4; uint32_t rx_watermark: 12; ///< FIFO RX watermark level uint32_t dw_dma_mts: 3; uint32_t reserved2: 1; }; uint32_t val; } fifoth; union { struct { uint32_t cards: 2; ///< bit N reads 0 if card N is present uint32_t reserved: 30; }; uint32_t val; } cdetect; union { struct { uint32_t cards: 2; ///< bit N reads 1 if card N is write protected uint32_t reserved: 30; }; uint32_t val; } wrtprt; uint32_t gpio; ///< unused uint32_t tcbcnt; ///< transferred (to card) byte count uint32_t tbbcnt; ///< transferred from host to FIFO byte count union { struct { uint32_t debounce_count: 24; ///< number of host cycles used by debounce filter, typical time should be 5-25ms uint32_t reserved: 8; }; } debnce; uint32_t usrid; ///< user ID uint32_t verid; ///< IP block version uint32_t hcon; ///< compile-time IP configuration union { struct { uint32_t voltage: 16; ///< voltage control for slots; no-op on ESP32. uint32_t ddr: 16; ///< bit N enables DDR mode for card N }; } uhs; ///< UHS related settings union { struct { uint32_t cards: 2; ///< bit N resets card N, active low uint32_t reserved: 30; }; } rst_n; uint32_t reserved_7c; union { struct { uint32_t sw_reset: 1; ///< set to reset DMA controller uint32_t fb: 1; ///< set if AHB master performs fixed burst transfers uint32_t dsl: 5; ///< descriptor skip length: number of words to skip between two unchained descriptors uint32_t enable: 1; ///< set to enable IDMAC uint32_t pbl: 3; ///< programmable burst length uint32_t reserved: 21; }; uint32_t val; } bmod; uint32_t pldmnd; ///< set any bit to resume IDMAC FSM from suspended state sdmmc_desc_t* dbaddr; ///< descriptor list base union { struct { uint32_t ti: 1; ///< transmit interrupt status uint32_t ri: 1; ///< receive interrupt status uint32_t fbe: 1; ///< fatal bus error uint32_t reserved1: 1; uint32_t du: 1; ///< descriptor unavailable uint32_t ces: 1; ///< card error summary uint32_t reserved2: 2; uint32_t nis: 1; ///< normal interrupt summary uint32_t fbe_code: 3; ///< code of fatal bus error uint32_t fsm: 4; ///< DMAC FSM state uint32_t reserved3: 15; }; uint32_t val; } idsts; union { struct { uint32_t ti: 1; ///< transmit interrupt enable uint32_t ri: 1; ///< receive interrupt enable uint32_t fbe: 1; ///< fatal bus error interrupt enable uint32_t reserved1: 1; uint32_t du: 1; ///< descriptor unavailable interrupt enable uint32_t ces: 1; ///< card error interrupt enable uint32_t reserved2: 2; uint32_t ni: 1; ///< normal interrupt interrupt enable uint32_t ai: 1; ///< abnormal interrupt enable uint32_t reserved3: 22; }; uint32_t val; } idinten; uint32_t dscaddr; ///< current host descriptor address uint32_t dscaddrl; ///< unused uint32_t dscaddru; ///< unused uint32_t bufaddrl; ///< unused uint32_t bufaddru; ///< unused uint32_t reserved_a8[22]; union { struct { uint32_t read_thr_en : 1; ///< initiate transfer only if FIFO has more space than the read threshold uint32_t busy_clr_int_en : 1; ///< enable generation of busy clear interrupts uint32_t write_thr_en : 1; ///< equivalent of read_thr_en for writes uint32_t reserved1 : 13; uint32_t card_threshold : 12; ///< threshold value for reads/writes, in bytes }; uint32_t val; } cardthrctl; uint32_t back_end_power; uint32_t uhs_reg_ext; uint32_t emmc_ddr_reg; uint32_t enable_shift; uint32_t reserved_114[443]; union { struct { uint32_t phase_dout: 3; ///< phase of data output clock (0x0: 0, 0x1: 90, 0x4: 180, 0x6: 270) uint32_t phase_din: 3; ///< phase of data input clock uint32_t phase_core: 3; ///< phase of the clock to SDMMC peripheral uint32_t div_factor_p: 4; ///< controls clock period; it will be (div_factor_p + 1) / 160MHz uint32_t div_factor_h: 4; ///< controls length of high pulse; it will be (div_factor_h + 1) / 160MHz uint32_t div_factor_m: 4; ///< should be equal to div_factor_p }; uint32_t val; } clock; } sdmmc_dev_t; extern sdmmc_dev_t SDMMC; _Static_assert(sizeof(sdmmc_dev_t) == 0x804, "invalid size of sdmmc_dev_t structure"); #ifdef __cplusplus } #endif #endif //_SOC_SDMMC_STRUCT_H_