arduino-esp32/tools/sdk/include/soc/soc/uhci_reg.h
2017-04-12 21:49:58 +03:00

1261 lines
56 KiB
C

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#ifndef _SOC_UHCI_REG_H_
#define _SOC_UHCI_REG_H_
#include "soc.h"
#define REG_UHCI_BASE(i) (DR_REG_UHCI0_BASE - (i) * 0x8000)
#define UHCI_CONF0_REG(i) (REG_UHCI_BASE(i) + 0x0)
/* UHCI_UART_RX_BRK_EOF_EN : R/W ;bitpos:[23] ;default: 1'b0 ; */
/*description: Set this bit to enable to use brk char as the end of a data frame.*/
#define UHCI_UART_RX_BRK_EOF_EN (BIT(23))
#define UHCI_UART_RX_BRK_EOF_EN_M (BIT(23))
#define UHCI_UART_RX_BRK_EOF_EN_V 0x1
#define UHCI_UART_RX_BRK_EOF_EN_S 23
/* UHCI_CLK_EN : R/W ;bitpos:[22] ;default: 1'b0 ; */
/*description: Set this bit to enable clock-gating for read or write registers.*/
#define UHCI_CLK_EN (BIT(22))
#define UHCI_CLK_EN_M (BIT(22))
#define UHCI_CLK_EN_V 0x1
#define UHCI_CLK_EN_S 22
/* UHCI_ENCODE_CRC_EN : R/W ;bitpos:[21] ;default: 1'b1 ; */
/*description: Set this bit to enable crc calculation for data frame when bit6
in the head packet is 1.*/
#define UHCI_ENCODE_CRC_EN (BIT(21))
#define UHCI_ENCODE_CRC_EN_M (BIT(21))
#define UHCI_ENCODE_CRC_EN_V 0x1
#define UHCI_ENCODE_CRC_EN_S 21
/* UHCI_LEN_EOF_EN : R/W ;bitpos:[20] ;default: 1'b1 ; */
/*description: Set this bit to enable to use packet_len in packet head when
the received data is equal to packet_len this means the end of a data frame.*/
#define UHCI_LEN_EOF_EN (BIT(20))
#define UHCI_LEN_EOF_EN_M (BIT(20))
#define UHCI_LEN_EOF_EN_V 0x1
#define UHCI_LEN_EOF_EN_S 20
/* UHCI_UART_IDLE_EOF_EN : R/W ;bitpos:[19] ;default: 1'b0 ; */
/*description: Set this bit to enable to use idle time when the idle time after
data frame is satisfied this means the end of a data frame.*/
#define UHCI_UART_IDLE_EOF_EN (BIT(19))
#define UHCI_UART_IDLE_EOF_EN_M (BIT(19))
#define UHCI_UART_IDLE_EOF_EN_V 0x1
#define UHCI_UART_IDLE_EOF_EN_S 19
/* UHCI_CRC_REC_EN : R/W ;bitpos:[18] ;default: 1'b1 ; */
/*description: Set this bit to enable receiver''s ability of crc calculation
when crc_en bit in head packet is 1 then there will be crc bytes after data_frame*/
#define UHCI_CRC_REC_EN (BIT(18))
#define UHCI_CRC_REC_EN_M (BIT(18))
#define UHCI_CRC_REC_EN_V 0x1
#define UHCI_CRC_REC_EN_S 18
/* UHCI_HEAD_EN : R/W ;bitpos:[17] ;default: 1'b1 ; */
/*description: Set this bit to enable to use head packet before the data frame.*/
#define UHCI_HEAD_EN (BIT(17))
#define UHCI_HEAD_EN_M (BIT(17))
#define UHCI_HEAD_EN_V 0x1
#define UHCI_HEAD_EN_S 17
/* UHCI_SEPER_EN : R/W ;bitpos:[16] ;default: 1'b1 ; */
/*description: Set this bit to use special char to separate the data frame.*/
#define UHCI_SEPER_EN (BIT(16))
#define UHCI_SEPER_EN_M (BIT(16))
#define UHCI_SEPER_EN_V 0x1
#define UHCI_SEPER_EN_S 16
/* UHCI_MEM_TRANS_EN : R/W ;bitpos:[15] ;default: 1'b0 ; */
/*description: */
#define UHCI_MEM_TRANS_EN (BIT(15))
#define UHCI_MEM_TRANS_EN_M (BIT(15))
#define UHCI_MEM_TRANS_EN_V 0x1
#define UHCI_MEM_TRANS_EN_S 15
/* UHCI_OUT_DATA_BURST_EN : R/W ;bitpos:[14] ;default: 1'b0 ; */
/*description: Set this bit to enable DMA burst MODE*/
#define UHCI_OUT_DATA_BURST_EN (BIT(14))
#define UHCI_OUT_DATA_BURST_EN_M (BIT(14))
#define UHCI_OUT_DATA_BURST_EN_V 0x1
#define UHCI_OUT_DATA_BURST_EN_S 14
/* UHCI_INDSCR_BURST_EN : R/W ;bitpos:[13] ;default: 1'b0 ; */
/*description: Set this bit to enable DMA out links to use burst mode.*/
#define UHCI_INDSCR_BURST_EN (BIT(13))
#define UHCI_INDSCR_BURST_EN_M (BIT(13))
#define UHCI_INDSCR_BURST_EN_V 0x1
#define UHCI_INDSCR_BURST_EN_S 13
/* UHCI_OUTDSCR_BURST_EN : R/W ;bitpos:[12] ;default: 1'b0 ; */
/*description: Set this bit to enable DMA in links to use burst mode.*/
#define UHCI_OUTDSCR_BURST_EN (BIT(12))
#define UHCI_OUTDSCR_BURST_EN_M (BIT(12))
#define UHCI_OUTDSCR_BURST_EN_V 0x1
#define UHCI_OUTDSCR_BURST_EN_S 12
/* UHCI_UART2_CE : R/W ;bitpos:[11] ;default: 1'b0 ; */
/*description: Set this bit to use UART2 to transmit or receive data.*/
#define UHCI_UART2_CE (BIT(11))
#define UHCI_UART2_CE_M (BIT(11))
#define UHCI_UART2_CE_V 0x1
#define UHCI_UART2_CE_S 11
/* UHCI_UART1_CE : R/W ;bitpos:[10] ;default: 1'b0 ; */
/*description: Set this bit to use UART1 to transmit or receive data.*/
#define UHCI_UART1_CE (BIT(10))
#define UHCI_UART1_CE_M (BIT(10))
#define UHCI_UART1_CE_V 0x1
#define UHCI_UART1_CE_S 10
/* UHCI_UART0_CE : R/W ;bitpos:[9] ;default: 1'b0 ; */
/*description: Set this bit to use UART to transmit or receive data.*/
#define UHCI_UART0_CE (BIT(9))
#define UHCI_UART0_CE_M (BIT(9))
#define UHCI_UART0_CE_V 0x1
#define UHCI_UART0_CE_S 9
/* UHCI_OUT_EOF_MODE : R/W ;bitpos:[8] ;default: 1'b1 ; */
/*description: Set this bit to produce eof after DMA pops all data clear this
bit to produce eof after DMA pushes all data*/
#define UHCI_OUT_EOF_MODE (BIT(8))
#define UHCI_OUT_EOF_MODE_M (BIT(8))
#define UHCI_OUT_EOF_MODE_V 0x1
#define UHCI_OUT_EOF_MODE_S 8
/* UHCI_OUT_NO_RESTART_CLR : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: don't use*/
#define UHCI_OUT_NO_RESTART_CLR (BIT(7))
#define UHCI_OUT_NO_RESTART_CLR_M (BIT(7))
#define UHCI_OUT_NO_RESTART_CLR_V 0x1
#define UHCI_OUT_NO_RESTART_CLR_S 7
/* UHCI_OUT_AUTO_WRBACK : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: when in link's length is 0 go on to use the next in link automatically.*/
#define UHCI_OUT_AUTO_WRBACK (BIT(6))
#define UHCI_OUT_AUTO_WRBACK_M (BIT(6))
#define UHCI_OUT_AUTO_WRBACK_V 0x1
#define UHCI_OUT_AUTO_WRBACK_S 6
/* UHCI_OUT_LOOP_TEST : R/W ;bitpos:[5] ;default: 1'b0 ; */
/*description: Set this bit to enable loop test for out links.*/
#define UHCI_OUT_LOOP_TEST (BIT(5))
#define UHCI_OUT_LOOP_TEST_M (BIT(5))
#define UHCI_OUT_LOOP_TEST_V 0x1
#define UHCI_OUT_LOOP_TEST_S 5
/* UHCI_IN_LOOP_TEST : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to enable loop test for in links.*/
#define UHCI_IN_LOOP_TEST (BIT(4))
#define UHCI_IN_LOOP_TEST_M (BIT(4))
#define UHCI_IN_LOOP_TEST_V 0x1
#define UHCI_IN_LOOP_TEST_S 4
/* UHCI_AHBM_RST : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to reset dma ahb interface.*/
#define UHCI_AHBM_RST (BIT(3))
#define UHCI_AHBM_RST_M (BIT(3))
#define UHCI_AHBM_RST_V 0x1
#define UHCI_AHBM_RST_S 3
/* UHCI_AHBM_FIFO_RST : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: Set this bit to reset dma ahb fifo.*/
#define UHCI_AHBM_FIFO_RST (BIT(2))
#define UHCI_AHBM_FIFO_RST_M (BIT(2))
#define UHCI_AHBM_FIFO_RST_V 0x1
#define UHCI_AHBM_FIFO_RST_S 2
/* UHCI_OUT_RST : R/W ;bitpos:[1] ;default: 1'b0 ; */
/*description: Set this bit to reset out link operations.*/
#define UHCI_OUT_RST (BIT(1))
#define UHCI_OUT_RST_M (BIT(1))
#define UHCI_OUT_RST_V 0x1
#define UHCI_OUT_RST_S 1
/* UHCI_IN_RST : R/W ;bitpos:[0] ;default: 1'h0 ; */
/*description: Set this bit to reset in link operations.*/
#define UHCI_IN_RST (BIT(0))
#define UHCI_IN_RST_M (BIT(0))
#define UHCI_IN_RST_V 0x1
#define UHCI_IN_RST_S 0
#define UHCI_INT_RAW_REG(i) (REG_UHCI_BASE(i) + 0x4)
/* UHCI_DMA_INFIFO_FULL_WM_INT_RAW : RO ;bitpos:[16] ;default: 1'b0 ; */
/*description: */
#define UHCI_DMA_INFIFO_FULL_WM_INT_RAW (BIT(16))
#define UHCI_DMA_INFIFO_FULL_WM_INT_RAW_M (BIT(16))
#define UHCI_DMA_INFIFO_FULL_WM_INT_RAW_V 0x1
#define UHCI_DMA_INFIFO_FULL_WM_INT_RAW_S 16
/* UHCI_SEND_A_Q_INT_RAW : RO ;bitpos:[15] ;default: 1'b0 ; */
/*description: When use always_send registers to send a series of short packets
it will produce this interrupt when dma has send the short packet.*/
#define UHCI_SEND_A_Q_INT_RAW (BIT(15))
#define UHCI_SEND_A_Q_INT_RAW_M (BIT(15))
#define UHCI_SEND_A_Q_INT_RAW_V 0x1
#define UHCI_SEND_A_Q_INT_RAW_S 15
/* UHCI_SEND_S_Q_INT_RAW : RO ;bitpos:[14] ;default: 1'b0 ; */
/*description: When use single send registers to send a short packets it will
produce this interrupt when dma has send the short packet.*/
#define UHCI_SEND_S_Q_INT_RAW (BIT(14))
#define UHCI_SEND_S_Q_INT_RAW_M (BIT(14))
#define UHCI_SEND_S_Q_INT_RAW_V 0x1
#define UHCI_SEND_S_Q_INT_RAW_S 14
/* UHCI_OUT_TOTAL_EOF_INT_RAW : RO ;bitpos:[13] ;default: 1'b0 ; */
/*description: When all data have been send it will produce uhci_out_total_eof_int interrupt.*/
#define UHCI_OUT_TOTAL_EOF_INT_RAW (BIT(13))
#define UHCI_OUT_TOTAL_EOF_INT_RAW_M (BIT(13))
#define UHCI_OUT_TOTAL_EOF_INT_RAW_V 0x1
#define UHCI_OUT_TOTAL_EOF_INT_RAW_S 13
/* UHCI_OUTLINK_EOF_ERR_INT_RAW : RO ;bitpos:[12] ;default: 1'b0 ; */
/*description: when there are some errors about eof in outlink descriptor it
will produce uhci_outlink_eof_err_int interrupt.*/
#define UHCI_OUTLINK_EOF_ERR_INT_RAW (BIT(12))
#define UHCI_OUTLINK_EOF_ERR_INT_RAW_M (BIT(12))
#define UHCI_OUTLINK_EOF_ERR_INT_RAW_V 0x1
#define UHCI_OUTLINK_EOF_ERR_INT_RAW_S 12
/* UHCI_IN_DSCR_EMPTY_INT_RAW : RO ;bitpos:[11] ;default: 1'b0 ; */
/*description: when there are not enough in links for DMA it will produce uhci_in_dscr_err_int
interrupt.*/
#define UHCI_IN_DSCR_EMPTY_INT_RAW (BIT(11))
#define UHCI_IN_DSCR_EMPTY_INT_RAW_M (BIT(11))
#define UHCI_IN_DSCR_EMPTY_INT_RAW_V 0x1
#define UHCI_IN_DSCR_EMPTY_INT_RAW_S 11
/* UHCI_OUT_DSCR_ERR_INT_RAW : RO ;bitpos:[10] ;default: 1'b0 ; */
/*description: when there are some errors about the in link descriptor it will
produce uhci_out_dscr_err_int interrupt.*/
#define UHCI_OUT_DSCR_ERR_INT_RAW (BIT(10))
#define UHCI_OUT_DSCR_ERR_INT_RAW_M (BIT(10))
#define UHCI_OUT_DSCR_ERR_INT_RAW_V 0x1
#define UHCI_OUT_DSCR_ERR_INT_RAW_S 10
/* UHCI_IN_DSCR_ERR_INT_RAW : RO ;bitpos:[9] ;default: 1'b0 ; */
/*description: when there are some errors about the out link descriptor it
will produce uhci_in_dscr_err_int interrupt.*/
#define UHCI_IN_DSCR_ERR_INT_RAW (BIT(9))
#define UHCI_IN_DSCR_ERR_INT_RAW_M (BIT(9))
#define UHCI_IN_DSCR_ERR_INT_RAW_V 0x1
#define UHCI_IN_DSCR_ERR_INT_RAW_S 9
/* UHCI_OUT_EOF_INT_RAW : RO ;bitpos:[8] ;default: 1'b0 ; */
/*description: when the current descriptor's eof bit is 1 it will produce uhci_out_eof_int
interrupt.*/
#define UHCI_OUT_EOF_INT_RAW (BIT(8))
#define UHCI_OUT_EOF_INT_RAW_M (BIT(8))
#define UHCI_OUT_EOF_INT_RAW_V 0x1
#define UHCI_OUT_EOF_INT_RAW_S 8
/* UHCI_OUT_DONE_INT_RAW : RO ;bitpos:[7] ;default: 1'b0 ; */
/*description: when a out link descriptor is completed it will produce uhci_out_done_int
interrupt.*/
#define UHCI_OUT_DONE_INT_RAW (BIT(7))
#define UHCI_OUT_DONE_INT_RAW_M (BIT(7))
#define UHCI_OUT_DONE_INT_RAW_V 0x1
#define UHCI_OUT_DONE_INT_RAW_S 7
/* UHCI_IN_ERR_EOF_INT_RAW : RO ;bitpos:[6] ;default: 1'b0 ; */
/*description: when there are some errors about eof in in link descriptor it
will produce uhci_in_err_eof_int interrupt.*/
#define UHCI_IN_ERR_EOF_INT_RAW (BIT(6))
#define UHCI_IN_ERR_EOF_INT_RAW_M (BIT(6))
#define UHCI_IN_ERR_EOF_INT_RAW_V 0x1
#define UHCI_IN_ERR_EOF_INT_RAW_S 6
/* UHCI_IN_SUC_EOF_INT_RAW : RO ;bitpos:[5] ;default: 1'b0 ; */
/*description: when a data packet has been received it will produce uhci_in_suc_eof_int
interrupt.*/
#define UHCI_IN_SUC_EOF_INT_RAW (BIT(5))
#define UHCI_IN_SUC_EOF_INT_RAW_M (BIT(5))
#define UHCI_IN_SUC_EOF_INT_RAW_V 0x1
#define UHCI_IN_SUC_EOF_INT_RAW_S 5
/* UHCI_IN_DONE_INT_RAW : RO ;bitpos:[4] ;default: 1'b0 ; */
/*description: when a in link descriptor has been completed it will produce
uhci_in_done_int interrupt.*/
#define UHCI_IN_DONE_INT_RAW (BIT(4))
#define UHCI_IN_DONE_INT_RAW_M (BIT(4))
#define UHCI_IN_DONE_INT_RAW_V 0x1
#define UHCI_IN_DONE_INT_RAW_S 4
/* UHCI_TX_HUNG_INT_RAW : RO ;bitpos:[3] ;default: 1'b0 ; */
/*description: when DMA takes a lot of time to read a data from RAM it will
produce uhci_tx_hung_int interrupt.*/
#define UHCI_TX_HUNG_INT_RAW (BIT(3))
#define UHCI_TX_HUNG_INT_RAW_M (BIT(3))
#define UHCI_TX_HUNG_INT_RAW_V 0x1
#define UHCI_TX_HUNG_INT_RAW_S 3
/* UHCI_RX_HUNG_INT_RAW : RO ;bitpos:[2] ;default: 1'b0 ; */
/*description: when DMA takes a lot of time to receive a data it will produce
uhci_rx_hung_int interrupt.*/
#define UHCI_RX_HUNG_INT_RAW (BIT(2))
#define UHCI_RX_HUNG_INT_RAW_M (BIT(2))
#define UHCI_RX_HUNG_INT_RAW_V 0x1
#define UHCI_RX_HUNG_INT_RAW_S 2
/* UHCI_TX_START_INT_RAW : RO ;bitpos:[1] ;default: 1'b0 ; */
/*description: when DMA detects a separator char it will produce uhci_tx_start_int interrupt.*/
#define UHCI_TX_START_INT_RAW (BIT(1))
#define UHCI_TX_START_INT_RAW_M (BIT(1))
#define UHCI_TX_START_INT_RAW_V 0x1
#define UHCI_TX_START_INT_RAW_S 1
/* UHCI_RX_START_INT_RAW : RO ;bitpos:[0] ;default: 1'b0 ; */
/*description: when a separator char has been send it will produce uhci_rx_start_int
interrupt.*/
#define UHCI_RX_START_INT_RAW (BIT(0))
#define UHCI_RX_START_INT_RAW_M (BIT(0))
#define UHCI_RX_START_INT_RAW_V 0x1
#define UHCI_RX_START_INT_RAW_S 0
#define UHCI_INT_ST_REG(i) (REG_UHCI_BASE(i) + 0x8)
/* UHCI_DMA_INFIFO_FULL_WM_INT_ST : RO ;bitpos:[16] ;default: 1'b0 ; */
/*description: */
#define UHCI_DMA_INFIFO_FULL_WM_INT_ST (BIT(16))
#define UHCI_DMA_INFIFO_FULL_WM_INT_ST_M (BIT(16))
#define UHCI_DMA_INFIFO_FULL_WM_INT_ST_V 0x1
#define UHCI_DMA_INFIFO_FULL_WM_INT_ST_S 16
/* UHCI_SEND_A_Q_INT_ST : RO ;bitpos:[15] ;default: 1'b0 ; */
/*description: */
#define UHCI_SEND_A_Q_INT_ST (BIT(15))
#define UHCI_SEND_A_Q_INT_ST_M (BIT(15))
#define UHCI_SEND_A_Q_INT_ST_V 0x1
#define UHCI_SEND_A_Q_INT_ST_S 15
/* UHCI_SEND_S_Q_INT_ST : RO ;bitpos:[14] ;default: 1'b0 ; */
/*description: */
#define UHCI_SEND_S_Q_INT_ST (BIT(14))
#define UHCI_SEND_S_Q_INT_ST_M (BIT(14))
#define UHCI_SEND_S_Q_INT_ST_V 0x1
#define UHCI_SEND_S_Q_INT_ST_S 14
/* UHCI_OUT_TOTAL_EOF_INT_ST : RO ;bitpos:[13] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_TOTAL_EOF_INT_ST (BIT(13))
#define UHCI_OUT_TOTAL_EOF_INT_ST_M (BIT(13))
#define UHCI_OUT_TOTAL_EOF_INT_ST_V 0x1
#define UHCI_OUT_TOTAL_EOF_INT_ST_S 13
/* UHCI_OUTLINK_EOF_ERR_INT_ST : RO ;bitpos:[12] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUTLINK_EOF_ERR_INT_ST (BIT(12))
#define UHCI_OUTLINK_EOF_ERR_INT_ST_M (BIT(12))
#define UHCI_OUTLINK_EOF_ERR_INT_ST_V 0x1
#define UHCI_OUTLINK_EOF_ERR_INT_ST_S 12
/* UHCI_IN_DSCR_EMPTY_INT_ST : RO ;bitpos:[11] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_DSCR_EMPTY_INT_ST (BIT(11))
#define UHCI_IN_DSCR_EMPTY_INT_ST_M (BIT(11))
#define UHCI_IN_DSCR_EMPTY_INT_ST_V 0x1
#define UHCI_IN_DSCR_EMPTY_INT_ST_S 11
/* UHCI_OUT_DSCR_ERR_INT_ST : RO ;bitpos:[10] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_DSCR_ERR_INT_ST (BIT(10))
#define UHCI_OUT_DSCR_ERR_INT_ST_M (BIT(10))
#define UHCI_OUT_DSCR_ERR_INT_ST_V 0x1
#define UHCI_OUT_DSCR_ERR_INT_ST_S 10
/* UHCI_IN_DSCR_ERR_INT_ST : RO ;bitpos:[9] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_DSCR_ERR_INT_ST (BIT(9))
#define UHCI_IN_DSCR_ERR_INT_ST_M (BIT(9))
#define UHCI_IN_DSCR_ERR_INT_ST_V 0x1
#define UHCI_IN_DSCR_ERR_INT_ST_S 9
/* UHCI_OUT_EOF_INT_ST : RO ;bitpos:[8] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_EOF_INT_ST (BIT(8))
#define UHCI_OUT_EOF_INT_ST_M (BIT(8))
#define UHCI_OUT_EOF_INT_ST_V 0x1
#define UHCI_OUT_EOF_INT_ST_S 8
/* UHCI_OUT_DONE_INT_ST : RO ;bitpos:[7] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_DONE_INT_ST (BIT(7))
#define UHCI_OUT_DONE_INT_ST_M (BIT(7))
#define UHCI_OUT_DONE_INT_ST_V 0x1
#define UHCI_OUT_DONE_INT_ST_S 7
/* UHCI_IN_ERR_EOF_INT_ST : RO ;bitpos:[6] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_ERR_EOF_INT_ST (BIT(6))
#define UHCI_IN_ERR_EOF_INT_ST_M (BIT(6))
#define UHCI_IN_ERR_EOF_INT_ST_V 0x1
#define UHCI_IN_ERR_EOF_INT_ST_S 6
/* UHCI_IN_SUC_EOF_INT_ST : RO ;bitpos:[5] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_SUC_EOF_INT_ST (BIT(5))
#define UHCI_IN_SUC_EOF_INT_ST_M (BIT(5))
#define UHCI_IN_SUC_EOF_INT_ST_V 0x1
#define UHCI_IN_SUC_EOF_INT_ST_S 5
/* UHCI_IN_DONE_INT_ST : RO ;bitpos:[4] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_DONE_INT_ST (BIT(4))
#define UHCI_IN_DONE_INT_ST_M (BIT(4))
#define UHCI_IN_DONE_INT_ST_V 0x1
#define UHCI_IN_DONE_INT_ST_S 4
/* UHCI_TX_HUNG_INT_ST : RO ;bitpos:[3] ;default: 1'b0 ; */
/*description: */
#define UHCI_TX_HUNG_INT_ST (BIT(3))
#define UHCI_TX_HUNG_INT_ST_M (BIT(3))
#define UHCI_TX_HUNG_INT_ST_V 0x1
#define UHCI_TX_HUNG_INT_ST_S 3
/* UHCI_RX_HUNG_INT_ST : RO ;bitpos:[2] ;default: 1'b0 ; */
/*description: */
#define UHCI_RX_HUNG_INT_ST (BIT(2))
#define UHCI_RX_HUNG_INT_ST_M (BIT(2))
#define UHCI_RX_HUNG_INT_ST_V 0x1
#define UHCI_RX_HUNG_INT_ST_S 2
/* UHCI_TX_START_INT_ST : RO ;bitpos:[1] ;default: 1'b0 ; */
/*description: */
#define UHCI_TX_START_INT_ST (BIT(1))
#define UHCI_TX_START_INT_ST_M (BIT(1))
#define UHCI_TX_START_INT_ST_V 0x1
#define UHCI_TX_START_INT_ST_S 1
/* UHCI_RX_START_INT_ST : RO ;bitpos:[0] ;default: 1'b0 ; */
/*description: */
#define UHCI_RX_START_INT_ST (BIT(0))
#define UHCI_RX_START_INT_ST_M (BIT(0))
#define UHCI_RX_START_INT_ST_V 0x1
#define UHCI_RX_START_INT_ST_S 0
#define UHCI_INT_ENA_REG(i) (REG_UHCI_BASE(i) + 0xC)
/* UHCI_DMA_INFIFO_FULL_WM_INT_ENA : R/W ;bitpos:[16] ;default: 1'b0 ; */
/*description: */
#define UHCI_DMA_INFIFO_FULL_WM_INT_ENA (BIT(16))
#define UHCI_DMA_INFIFO_FULL_WM_INT_ENA_M (BIT(16))
#define UHCI_DMA_INFIFO_FULL_WM_INT_ENA_V 0x1
#define UHCI_DMA_INFIFO_FULL_WM_INT_ENA_S 16
/* UHCI_SEND_A_Q_INT_ENA : R/W ;bitpos:[15] ;default: 1'b0 ; */
/*description: */
#define UHCI_SEND_A_Q_INT_ENA (BIT(15))
#define UHCI_SEND_A_Q_INT_ENA_M (BIT(15))
#define UHCI_SEND_A_Q_INT_ENA_V 0x1
#define UHCI_SEND_A_Q_INT_ENA_S 15
/* UHCI_SEND_S_Q_INT_ENA : R/W ;bitpos:[14] ;default: 1'b0 ; */
/*description: */
#define UHCI_SEND_S_Q_INT_ENA (BIT(14))
#define UHCI_SEND_S_Q_INT_ENA_M (BIT(14))
#define UHCI_SEND_S_Q_INT_ENA_V 0x1
#define UHCI_SEND_S_Q_INT_ENA_S 14
/* UHCI_OUT_TOTAL_EOF_INT_ENA : R/W ;bitpos:[13] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_TOTAL_EOF_INT_ENA (BIT(13))
#define UHCI_OUT_TOTAL_EOF_INT_ENA_M (BIT(13))
#define UHCI_OUT_TOTAL_EOF_INT_ENA_V 0x1
#define UHCI_OUT_TOTAL_EOF_INT_ENA_S 13
/* UHCI_OUTLINK_EOF_ERR_INT_ENA : R/W ;bitpos:[12] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUTLINK_EOF_ERR_INT_ENA (BIT(12))
#define UHCI_OUTLINK_EOF_ERR_INT_ENA_M (BIT(12))
#define UHCI_OUTLINK_EOF_ERR_INT_ENA_V 0x1
#define UHCI_OUTLINK_EOF_ERR_INT_ENA_S 12
/* UHCI_IN_DSCR_EMPTY_INT_ENA : R/W ;bitpos:[11] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_DSCR_EMPTY_INT_ENA (BIT(11))
#define UHCI_IN_DSCR_EMPTY_INT_ENA_M (BIT(11))
#define UHCI_IN_DSCR_EMPTY_INT_ENA_V 0x1
#define UHCI_IN_DSCR_EMPTY_INT_ENA_S 11
/* UHCI_OUT_DSCR_ERR_INT_ENA : R/W ;bitpos:[10] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_DSCR_ERR_INT_ENA (BIT(10))
#define UHCI_OUT_DSCR_ERR_INT_ENA_M (BIT(10))
#define UHCI_OUT_DSCR_ERR_INT_ENA_V 0x1
#define UHCI_OUT_DSCR_ERR_INT_ENA_S 10
/* UHCI_IN_DSCR_ERR_INT_ENA : R/W ;bitpos:[9] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_DSCR_ERR_INT_ENA (BIT(9))
#define UHCI_IN_DSCR_ERR_INT_ENA_M (BIT(9))
#define UHCI_IN_DSCR_ERR_INT_ENA_V 0x1
#define UHCI_IN_DSCR_ERR_INT_ENA_S 9
/* UHCI_OUT_EOF_INT_ENA : R/W ;bitpos:[8] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_EOF_INT_ENA (BIT(8))
#define UHCI_OUT_EOF_INT_ENA_M (BIT(8))
#define UHCI_OUT_EOF_INT_ENA_V 0x1
#define UHCI_OUT_EOF_INT_ENA_S 8
/* UHCI_OUT_DONE_INT_ENA : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_DONE_INT_ENA (BIT(7))
#define UHCI_OUT_DONE_INT_ENA_M (BIT(7))
#define UHCI_OUT_DONE_INT_ENA_V 0x1
#define UHCI_OUT_DONE_INT_ENA_S 7
/* UHCI_IN_ERR_EOF_INT_ENA : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_ERR_EOF_INT_ENA (BIT(6))
#define UHCI_IN_ERR_EOF_INT_ENA_M (BIT(6))
#define UHCI_IN_ERR_EOF_INT_ENA_V 0x1
#define UHCI_IN_ERR_EOF_INT_ENA_S 6
/* UHCI_IN_SUC_EOF_INT_ENA : R/W ;bitpos:[5] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_SUC_EOF_INT_ENA (BIT(5))
#define UHCI_IN_SUC_EOF_INT_ENA_M (BIT(5))
#define UHCI_IN_SUC_EOF_INT_ENA_V 0x1
#define UHCI_IN_SUC_EOF_INT_ENA_S 5
/* UHCI_IN_DONE_INT_ENA : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_DONE_INT_ENA (BIT(4))
#define UHCI_IN_DONE_INT_ENA_M (BIT(4))
#define UHCI_IN_DONE_INT_ENA_V 0x1
#define UHCI_IN_DONE_INT_ENA_S 4
/* UHCI_TX_HUNG_INT_ENA : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: */
#define UHCI_TX_HUNG_INT_ENA (BIT(3))
#define UHCI_TX_HUNG_INT_ENA_M (BIT(3))
#define UHCI_TX_HUNG_INT_ENA_V 0x1
#define UHCI_TX_HUNG_INT_ENA_S 3
/* UHCI_RX_HUNG_INT_ENA : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: */
#define UHCI_RX_HUNG_INT_ENA (BIT(2))
#define UHCI_RX_HUNG_INT_ENA_M (BIT(2))
#define UHCI_RX_HUNG_INT_ENA_V 0x1
#define UHCI_RX_HUNG_INT_ENA_S 2
/* UHCI_TX_START_INT_ENA : R/W ;bitpos:[1] ;default: 1'b0 ; */
/*description: */
#define UHCI_TX_START_INT_ENA (BIT(1))
#define UHCI_TX_START_INT_ENA_M (BIT(1))
#define UHCI_TX_START_INT_ENA_V 0x1
#define UHCI_TX_START_INT_ENA_S 1
/* UHCI_RX_START_INT_ENA : R/W ;bitpos:[0] ;default: 1'b0 ; */
/*description: */
#define UHCI_RX_START_INT_ENA (BIT(0))
#define UHCI_RX_START_INT_ENA_M (BIT(0))
#define UHCI_RX_START_INT_ENA_V 0x1
#define UHCI_RX_START_INT_ENA_S 0
#define UHCI_INT_CLR_REG(i) (REG_UHCI_BASE(i) + 0x10)
/* UHCI_DMA_INFIFO_FULL_WM_INT_CLR : WO ;bitpos:[16] ;default: 1'b0 ; */
/*description: */
#define UHCI_DMA_INFIFO_FULL_WM_INT_CLR (BIT(16))
#define UHCI_DMA_INFIFO_FULL_WM_INT_CLR_M (BIT(16))
#define UHCI_DMA_INFIFO_FULL_WM_INT_CLR_V 0x1
#define UHCI_DMA_INFIFO_FULL_WM_INT_CLR_S 16
/* UHCI_SEND_A_Q_INT_CLR : WO ;bitpos:[15] ;default: 1'b0 ; */
/*description: */
#define UHCI_SEND_A_Q_INT_CLR (BIT(15))
#define UHCI_SEND_A_Q_INT_CLR_M (BIT(15))
#define UHCI_SEND_A_Q_INT_CLR_V 0x1
#define UHCI_SEND_A_Q_INT_CLR_S 15
/* UHCI_SEND_S_Q_INT_CLR : WO ;bitpos:[14] ;default: 1'b0 ; */
/*description: */
#define UHCI_SEND_S_Q_INT_CLR (BIT(14))
#define UHCI_SEND_S_Q_INT_CLR_M (BIT(14))
#define UHCI_SEND_S_Q_INT_CLR_V 0x1
#define UHCI_SEND_S_Q_INT_CLR_S 14
/* UHCI_OUT_TOTAL_EOF_INT_CLR : WO ;bitpos:[13] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_TOTAL_EOF_INT_CLR (BIT(13))
#define UHCI_OUT_TOTAL_EOF_INT_CLR_M (BIT(13))
#define UHCI_OUT_TOTAL_EOF_INT_CLR_V 0x1
#define UHCI_OUT_TOTAL_EOF_INT_CLR_S 13
/* UHCI_OUTLINK_EOF_ERR_INT_CLR : WO ;bitpos:[12] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUTLINK_EOF_ERR_INT_CLR (BIT(12))
#define UHCI_OUTLINK_EOF_ERR_INT_CLR_M (BIT(12))
#define UHCI_OUTLINK_EOF_ERR_INT_CLR_V 0x1
#define UHCI_OUTLINK_EOF_ERR_INT_CLR_S 12
/* UHCI_IN_DSCR_EMPTY_INT_CLR : WO ;bitpos:[11] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_DSCR_EMPTY_INT_CLR (BIT(11))
#define UHCI_IN_DSCR_EMPTY_INT_CLR_M (BIT(11))
#define UHCI_IN_DSCR_EMPTY_INT_CLR_V 0x1
#define UHCI_IN_DSCR_EMPTY_INT_CLR_S 11
/* UHCI_OUT_DSCR_ERR_INT_CLR : WO ;bitpos:[10] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_DSCR_ERR_INT_CLR (BIT(10))
#define UHCI_OUT_DSCR_ERR_INT_CLR_M (BIT(10))
#define UHCI_OUT_DSCR_ERR_INT_CLR_V 0x1
#define UHCI_OUT_DSCR_ERR_INT_CLR_S 10
/* UHCI_IN_DSCR_ERR_INT_CLR : WO ;bitpos:[9] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_DSCR_ERR_INT_CLR (BIT(9))
#define UHCI_IN_DSCR_ERR_INT_CLR_M (BIT(9))
#define UHCI_IN_DSCR_ERR_INT_CLR_V 0x1
#define UHCI_IN_DSCR_ERR_INT_CLR_S 9
/* UHCI_OUT_EOF_INT_CLR : WO ;bitpos:[8] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_EOF_INT_CLR (BIT(8))
#define UHCI_OUT_EOF_INT_CLR_M (BIT(8))
#define UHCI_OUT_EOF_INT_CLR_V 0x1
#define UHCI_OUT_EOF_INT_CLR_S 8
/* UHCI_OUT_DONE_INT_CLR : WO ;bitpos:[7] ;default: 1'b0 ; */
/*description: */
#define UHCI_OUT_DONE_INT_CLR (BIT(7))
#define UHCI_OUT_DONE_INT_CLR_M (BIT(7))
#define UHCI_OUT_DONE_INT_CLR_V 0x1
#define UHCI_OUT_DONE_INT_CLR_S 7
/* UHCI_IN_ERR_EOF_INT_CLR : WO ;bitpos:[6] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_ERR_EOF_INT_CLR (BIT(6))
#define UHCI_IN_ERR_EOF_INT_CLR_M (BIT(6))
#define UHCI_IN_ERR_EOF_INT_CLR_V 0x1
#define UHCI_IN_ERR_EOF_INT_CLR_S 6
/* UHCI_IN_SUC_EOF_INT_CLR : WO ;bitpos:[5] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_SUC_EOF_INT_CLR (BIT(5))
#define UHCI_IN_SUC_EOF_INT_CLR_M (BIT(5))
#define UHCI_IN_SUC_EOF_INT_CLR_V 0x1
#define UHCI_IN_SUC_EOF_INT_CLR_S 5
/* UHCI_IN_DONE_INT_CLR : WO ;bitpos:[4] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_DONE_INT_CLR (BIT(4))
#define UHCI_IN_DONE_INT_CLR_M (BIT(4))
#define UHCI_IN_DONE_INT_CLR_V 0x1
#define UHCI_IN_DONE_INT_CLR_S 4
/* UHCI_TX_HUNG_INT_CLR : WO ;bitpos:[3] ;default: 1'b0 ; */
/*description: */
#define UHCI_TX_HUNG_INT_CLR (BIT(3))
#define UHCI_TX_HUNG_INT_CLR_M (BIT(3))
#define UHCI_TX_HUNG_INT_CLR_V 0x1
#define UHCI_TX_HUNG_INT_CLR_S 3
/* UHCI_RX_HUNG_INT_CLR : WO ;bitpos:[2] ;default: 1'b0 ; */
/*description: */
#define UHCI_RX_HUNG_INT_CLR (BIT(2))
#define UHCI_RX_HUNG_INT_CLR_M (BIT(2))
#define UHCI_RX_HUNG_INT_CLR_V 0x1
#define UHCI_RX_HUNG_INT_CLR_S 2
/* UHCI_TX_START_INT_CLR : WO ;bitpos:[1] ;default: 1'b0 ; */
/*description: */
#define UHCI_TX_START_INT_CLR (BIT(1))
#define UHCI_TX_START_INT_CLR_M (BIT(1))
#define UHCI_TX_START_INT_CLR_V 0x1
#define UHCI_TX_START_INT_CLR_S 1
/* UHCI_RX_START_INT_CLR : WO ;bitpos:[0] ;default: 1'b0 ; */
/*description: */
#define UHCI_RX_START_INT_CLR (BIT(0))
#define UHCI_RX_START_INT_CLR_M (BIT(0))
#define UHCI_RX_START_INT_CLR_V 0x1
#define UHCI_RX_START_INT_CLR_S 0
#define UHCI_DMA_OUT_STATUS_REG(i) (REG_UHCI_BASE(i) + 0x14)
/* UHCI_OUT_EMPTY : RO ;bitpos:[1] ;default: 1'b1 ; */
/*description: 1:DMA in link descriptor's fifo is empty.*/
#define UHCI_OUT_EMPTY (BIT(1))
#define UHCI_OUT_EMPTY_M (BIT(1))
#define UHCI_OUT_EMPTY_V 0x1
#define UHCI_OUT_EMPTY_S 1
/* UHCI_OUT_FULL : RO ;bitpos:[0] ;default: 1'b0 ; */
/*description: 1:DMA out link descriptor's fifo is full.*/
#define UHCI_OUT_FULL (BIT(0))
#define UHCI_OUT_FULL_M (BIT(0))
#define UHCI_OUT_FULL_V 0x1
#define UHCI_OUT_FULL_S 0
#define UHCI_DMA_OUT_PUSH_REG(i) (REG_UHCI_BASE(i) + 0x18)
/* UHCI_OUTFIFO_PUSH : R/W ;bitpos:[16] ;default: 1'h0 ; */
/*description: Set this bit to push data in out link descriptor's fifo.*/
#define UHCI_OUTFIFO_PUSH (BIT(16))
#define UHCI_OUTFIFO_PUSH_M (BIT(16))
#define UHCI_OUTFIFO_PUSH_V 0x1
#define UHCI_OUTFIFO_PUSH_S 16
/* UHCI_OUTFIFO_WDATA : R/W ;bitpos:[8:0] ;default: 9'h0 ; */
/*description: This is the data need to be pushed into out link descriptor's fifo.*/
#define UHCI_OUTFIFO_WDATA 0x000001FF
#define UHCI_OUTFIFO_WDATA_M ((UHCI_OUTFIFO_WDATA_V)<<(UHCI_OUTFIFO_WDATA_S))
#define UHCI_OUTFIFO_WDATA_V 0x1FF
#define UHCI_OUTFIFO_WDATA_S 0
#define UHCI_DMA_IN_STATUS_REG(i) (REG_UHCI_BASE(i) + 0x1C)
/* UHCI_RX_ERR_CAUSE : RO ;bitpos:[6:4] ;default: 3'h0 ; */
/*description: This register stores the errors caused in out link descriptor's data packet.*/
#define UHCI_RX_ERR_CAUSE 0x00000007
#define UHCI_RX_ERR_CAUSE_M ((UHCI_RX_ERR_CAUSE_V)<<(UHCI_RX_ERR_CAUSE_S))
#define UHCI_RX_ERR_CAUSE_V 0x7
#define UHCI_RX_ERR_CAUSE_S 4
/* UHCI_IN_EMPTY : RO ;bitpos:[1] ;default: 1'b1 ; */
/*description: */
#define UHCI_IN_EMPTY (BIT(1))
#define UHCI_IN_EMPTY_M (BIT(1))
#define UHCI_IN_EMPTY_V 0x1
#define UHCI_IN_EMPTY_S 1
/* UHCI_IN_FULL : RO ;bitpos:[0] ;default: 1'b0 ; */
/*description: */
#define UHCI_IN_FULL (BIT(0))
#define UHCI_IN_FULL_M (BIT(0))
#define UHCI_IN_FULL_V 0x1
#define UHCI_IN_FULL_S 0
#define UHCI_DMA_IN_POP_REG(i) (REG_UHCI_BASE(i) + 0x20)
/* UHCI_INFIFO_POP : R/W ;bitpos:[16] ;default: 1'h0 ; */
/*description: Set this bit to pop data in in link descriptor's fifo.*/
#define UHCI_INFIFO_POP (BIT(16))
#define UHCI_INFIFO_POP_M (BIT(16))
#define UHCI_INFIFO_POP_V 0x1
#define UHCI_INFIFO_POP_S 16
/* UHCI_INFIFO_RDATA : RO ;bitpos:[11:0] ;default: 12'h0 ; */
/*description: This register stores the data pop from in link descriptor's fifo.*/
#define UHCI_INFIFO_RDATA 0x00000FFF
#define UHCI_INFIFO_RDATA_M ((UHCI_INFIFO_RDATA_V)<<(UHCI_INFIFO_RDATA_S))
#define UHCI_INFIFO_RDATA_V 0xFFF
#define UHCI_INFIFO_RDATA_S 0
#define UHCI_DMA_OUT_LINK_REG(i) (REG_UHCI_BASE(i) + 0x24)
/* UHCI_OUTLINK_PARK : RO ;bitpos:[31] ;default: 1'h0 ; */
/*description: 1£º the out link descriptor's fsm is in idle state. 0:the out
link descriptor's fsm is working.*/
#define UHCI_OUTLINK_PARK (BIT(31))
#define UHCI_OUTLINK_PARK_M (BIT(31))
#define UHCI_OUTLINK_PARK_V 0x1
#define UHCI_OUTLINK_PARK_S 31
/* UHCI_OUTLINK_RESTART : R/W ;bitpos:[30] ;default: 1'b0 ; */
/*description: Set this bit to mount on new out link descriptors*/
#define UHCI_OUTLINK_RESTART (BIT(30))
#define UHCI_OUTLINK_RESTART_M (BIT(30))
#define UHCI_OUTLINK_RESTART_V 0x1
#define UHCI_OUTLINK_RESTART_S 30
/* UHCI_OUTLINK_START : R/W ;bitpos:[29] ;default: 1'b0 ; */
/*description: Set this bit to start dealing with the out link descriptors.*/
#define UHCI_OUTLINK_START (BIT(29))
#define UHCI_OUTLINK_START_M (BIT(29))
#define UHCI_OUTLINK_START_V 0x1
#define UHCI_OUTLINK_START_S 29
/* UHCI_OUTLINK_STOP : R/W ;bitpos:[28] ;default: 1'b0 ; */
/*description: Set this bit to stop dealing with the out link descriptors.*/
#define UHCI_OUTLINK_STOP (BIT(28))
#define UHCI_OUTLINK_STOP_M (BIT(28))
#define UHCI_OUTLINK_STOP_V 0x1
#define UHCI_OUTLINK_STOP_S 28
/* UHCI_OUTLINK_ADDR : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: This register stores the least 20 bits of the first out link
descriptor's address.*/
#define UHCI_OUTLINK_ADDR 0x000FFFFF
#define UHCI_OUTLINK_ADDR_M ((UHCI_OUTLINK_ADDR_V)<<(UHCI_OUTLINK_ADDR_S))
#define UHCI_OUTLINK_ADDR_V 0xFFFFF
#define UHCI_OUTLINK_ADDR_S 0
#define UHCI_DMA_IN_LINK_REG(i) (REG_UHCI_BASE(i) + 0x28)
/* UHCI_INLINK_PARK : RO ;bitpos:[31] ;default: 1'h0 ; */
/*description: 1:the in link descriptor's fsm is in idle state. 0:the in link
descriptor's fsm is working*/
#define UHCI_INLINK_PARK (BIT(31))
#define UHCI_INLINK_PARK_M (BIT(31))
#define UHCI_INLINK_PARK_V 0x1
#define UHCI_INLINK_PARK_S 31
/* UHCI_INLINK_RESTART : R/W ;bitpos:[30] ;default: 1'b0 ; */
/*description: Set this bit to mount on new in link descriptors*/
#define UHCI_INLINK_RESTART (BIT(30))
#define UHCI_INLINK_RESTART_M (BIT(30))
#define UHCI_INLINK_RESTART_V 0x1
#define UHCI_INLINK_RESTART_S 30
/* UHCI_INLINK_START : R/W ;bitpos:[29] ;default: 1'b0 ; */
/*description: Set this bit to start dealing with the in link descriptors.*/
#define UHCI_INLINK_START (BIT(29))
#define UHCI_INLINK_START_M (BIT(29))
#define UHCI_INLINK_START_V 0x1
#define UHCI_INLINK_START_S 29
/* UHCI_INLINK_STOP : R/W ;bitpos:[28] ;default: 1'b0 ; */
/*description: Set this bit to stop dealing with the in link descriptors.*/
#define UHCI_INLINK_STOP (BIT(28))
#define UHCI_INLINK_STOP_M (BIT(28))
#define UHCI_INLINK_STOP_V 0x1
#define UHCI_INLINK_STOP_S 28
/* UHCI_INLINK_AUTO_RET : R/W ;bitpos:[20] ;default: 1'b1 ; */
/*description: 1:when a packet is wrong in link descriptor returns to the descriptor
which is lately used.*/
#define UHCI_INLINK_AUTO_RET (BIT(20))
#define UHCI_INLINK_AUTO_RET_M (BIT(20))
#define UHCI_INLINK_AUTO_RET_V 0x1
#define UHCI_INLINK_AUTO_RET_S 20
/* UHCI_INLINK_ADDR : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: This register stores the least 20 bits of the first in link descriptor's
address.*/
#define UHCI_INLINK_ADDR 0x000FFFFF
#define UHCI_INLINK_ADDR_M ((UHCI_INLINK_ADDR_V)<<(UHCI_INLINK_ADDR_S))
#define UHCI_INLINK_ADDR_V 0xFFFFF
#define UHCI_INLINK_ADDR_S 0
#define UHCI_CONF1_REG(i) (REG_UHCI_BASE(i) + 0x2C)
/* UHCI_DMA_INFIFO_FULL_THRS : R/W ;bitpos:[20:9] ;default: 12'b0 ; */
/*description: when data amount in link descriptor's fifo is more than this
register value it will produce uhci_dma_infifo_full_wm_int interrupt.*/
#define UHCI_DMA_INFIFO_FULL_THRS 0x00000FFF
#define UHCI_DMA_INFIFO_FULL_THRS_M ((UHCI_DMA_INFIFO_FULL_THRS_V)<<(UHCI_DMA_INFIFO_FULL_THRS_S))
#define UHCI_DMA_INFIFO_FULL_THRS_V 0xFFF
#define UHCI_DMA_INFIFO_FULL_THRS_S 9
/* UHCI_SW_START : R/W ;bitpos:[8] ;default: 1'b0 ; */
/*description: Set this bit to start inserting the packet header.*/
#define UHCI_SW_START (BIT(8))
#define UHCI_SW_START_M (BIT(8))
#define UHCI_SW_START_V 0x1
#define UHCI_SW_START_S 8
/* UHCI_WAIT_SW_START : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: Set this bit to enable software way to add packet header.*/
#define UHCI_WAIT_SW_START (BIT(7))
#define UHCI_WAIT_SW_START_M (BIT(7))
#define UHCI_WAIT_SW_START_V 0x1
#define UHCI_WAIT_SW_START_S 7
/* UHCI_CHECK_OWNER : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to check the owner bit in link descriptor.*/
#define UHCI_CHECK_OWNER (BIT(6))
#define UHCI_CHECK_OWNER_M (BIT(6))
#define UHCI_CHECK_OWNER_V 0x1
#define UHCI_CHECK_OWNER_S 6
/* UHCI_TX_ACK_NUM_RE : R/W ;bitpos:[5] ;default: 1'b1 ; */
/*description: Set this bit to enable hardware replace ack num in packet header automatically.*/
#define UHCI_TX_ACK_NUM_RE (BIT(5))
#define UHCI_TX_ACK_NUM_RE_M (BIT(5))
#define UHCI_TX_ACK_NUM_RE_V 0x1
#define UHCI_TX_ACK_NUM_RE_S 5
/* UHCI_TX_CHECK_SUM_RE : R/W ;bitpos:[4] ;default: 1'b1 ; */
/*description: Set this bit to enable hardware replace check_sum in packet header
automatically.*/
#define UHCI_TX_CHECK_SUM_RE (BIT(4))
#define UHCI_TX_CHECK_SUM_RE_M (BIT(4))
#define UHCI_TX_CHECK_SUM_RE_V 0x1
#define UHCI_TX_CHECK_SUM_RE_S 4
/* UHCI_SAVE_HEAD : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to save packet header .*/
#define UHCI_SAVE_HEAD (BIT(3))
#define UHCI_SAVE_HEAD_M (BIT(3))
#define UHCI_SAVE_HEAD_V 0x1
#define UHCI_SAVE_HEAD_S 3
/* UHCI_CRC_DISABLE : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: Set this bit to disable crc calculation.*/
#define UHCI_CRC_DISABLE (BIT(2))
#define UHCI_CRC_DISABLE_M (BIT(2))
#define UHCI_CRC_DISABLE_V 0x1
#define UHCI_CRC_DISABLE_S 2
/* UHCI_CHECK_SEQ_EN : R/W ;bitpos:[1] ;default: 1'b1 ; */
/*description: Set this bit to enable decoder to check seq num in packet header.*/
#define UHCI_CHECK_SEQ_EN (BIT(1))
#define UHCI_CHECK_SEQ_EN_M (BIT(1))
#define UHCI_CHECK_SEQ_EN_V 0x1
#define UHCI_CHECK_SEQ_EN_S 1
/* UHCI_CHECK_SUM_EN : R/W ;bitpos:[0] ;default: 1'b1 ; */
/*description: Set this bit to enable decoder to check check_sum in packet header.*/
#define UHCI_CHECK_SUM_EN (BIT(0))
#define UHCI_CHECK_SUM_EN_M (BIT(0))
#define UHCI_CHECK_SUM_EN_V 0x1
#define UHCI_CHECK_SUM_EN_S 0
#define UHCI_STATE0_REG(i) (REG_UHCI_BASE(i) + 0x30)
/* UHCI_STATE0 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: */
#define UHCI_STATE0 0xFFFFFFFF
#define UHCI_STATE0_M ((UHCI_STATE0_V)<<(UHCI_STATE0_S))
#define UHCI_STATE0_V 0xFFFFFFFF
#define UHCI_STATE0_S 0
#define UHCI_STATE1_REG(i) (REG_UHCI_BASE(i) + 0x34)
/* UHCI_STATE1 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: */
#define UHCI_STATE1 0xFFFFFFFF
#define UHCI_STATE1_M ((UHCI_STATE1_V)<<(UHCI_STATE1_S))
#define UHCI_STATE1_V 0xFFFFFFFF
#define UHCI_STATE1_S 0
#define UHCI_DMA_OUT_EOF_DES_ADDR_REG(i) (REG_UHCI_BASE(i) + 0x38)
/* UHCI_OUT_EOF_DES_ADDR : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the address of out link descriptoir when
eof bit in this descriptor is 1.*/
#define UHCI_OUT_EOF_DES_ADDR 0xFFFFFFFF
#define UHCI_OUT_EOF_DES_ADDR_M ((UHCI_OUT_EOF_DES_ADDR_V)<<(UHCI_OUT_EOF_DES_ADDR_S))
#define UHCI_OUT_EOF_DES_ADDR_V 0xFFFFFFFF
#define UHCI_OUT_EOF_DES_ADDR_S 0
#define UHCI_DMA_IN_SUC_EOF_DES_ADDR_REG(i) (REG_UHCI_BASE(i) + 0x3C)
/* UHCI_IN_SUC_EOF_DES_ADDR : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the address of in link descriptor when eof
bit in this descriptor is 1.*/
#define UHCI_IN_SUC_EOF_DES_ADDR 0xFFFFFFFF
#define UHCI_IN_SUC_EOF_DES_ADDR_M ((UHCI_IN_SUC_EOF_DES_ADDR_V)<<(UHCI_IN_SUC_EOF_DES_ADDR_S))
#define UHCI_IN_SUC_EOF_DES_ADDR_V 0xFFFFFFFF
#define UHCI_IN_SUC_EOF_DES_ADDR_S 0
#define UHCI_DMA_IN_ERR_EOF_DES_ADDR_REG(i) (REG_UHCI_BASE(i) + 0x40)
/* UHCI_IN_ERR_EOF_DES_ADDR : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the address of in link descriptor when there
are some errors in this descriptor.*/
#define UHCI_IN_ERR_EOF_DES_ADDR 0xFFFFFFFF
#define UHCI_IN_ERR_EOF_DES_ADDR_M ((UHCI_IN_ERR_EOF_DES_ADDR_V)<<(UHCI_IN_ERR_EOF_DES_ADDR_S))
#define UHCI_IN_ERR_EOF_DES_ADDR_V 0xFFFFFFFF
#define UHCI_IN_ERR_EOF_DES_ADDR_S 0
#define UHCI_DMA_OUT_EOF_BFR_DES_ADDR_REG(i) (REG_UHCI_BASE(i) + 0x44)
/* UHCI_OUT_EOF_BFR_DES_ADDR : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the address of out link descriptor when
there are some errors in this descriptor.*/
#define UHCI_OUT_EOF_BFR_DES_ADDR 0xFFFFFFFF
#define UHCI_OUT_EOF_BFR_DES_ADDR_M ((UHCI_OUT_EOF_BFR_DES_ADDR_V)<<(UHCI_OUT_EOF_BFR_DES_ADDR_S))
#define UHCI_OUT_EOF_BFR_DES_ADDR_V 0xFFFFFFFF
#define UHCI_OUT_EOF_BFR_DES_ADDR_S 0
#define UHCI_AHB_TEST_REG(i) (REG_UHCI_BASE(i) + 0x48)
/* UHCI_AHB_TESTADDR : R/W ;bitpos:[5:4] ;default: 2'b0 ; */
/*description: The two bits represent ahb bus address bit[20:19]*/
#define UHCI_AHB_TESTADDR 0x00000003
#define UHCI_AHB_TESTADDR_M ((UHCI_AHB_TESTADDR_V)<<(UHCI_AHB_TESTADDR_S))
#define UHCI_AHB_TESTADDR_V 0x3
#define UHCI_AHB_TESTADDR_S 4
/* UHCI_AHB_TESTMODE : R/W ;bitpos:[2:0] ;default: 3'b0 ; */
/*description: bit2 is ahb bus test enable ,bit1 is used to choose wrtie(1)
or read(0) mode. bit0 is used to choose test only once(1) or continue(0)*/
#define UHCI_AHB_TESTMODE 0x00000007
#define UHCI_AHB_TESTMODE_M ((UHCI_AHB_TESTMODE_V)<<(UHCI_AHB_TESTMODE_S))
#define UHCI_AHB_TESTMODE_V 0x7
#define UHCI_AHB_TESTMODE_S 0
#define UHCI_DMA_IN_DSCR_REG(i) (REG_UHCI_BASE(i) + 0x4C)
/* UHCI_INLINK_DSCR : RO ;bitpos:[31:0] ;default: 32'b0 ; */
/*description: The content of current in link descriptor's third dword*/
#define UHCI_INLINK_DSCR 0xFFFFFFFF
#define UHCI_INLINK_DSCR_M ((UHCI_INLINK_DSCR_V)<<(UHCI_INLINK_DSCR_S))
#define UHCI_INLINK_DSCR_V 0xFFFFFFFF
#define UHCI_INLINK_DSCR_S 0
#define UHCI_DMA_IN_DSCR_BF0_REG(i) (REG_UHCI_BASE(i) + 0x50)
/* UHCI_INLINK_DSCR_BF0 : RO ;bitpos:[31:0] ;default: 32'b0 ; */
/*description: The content of current in link descriptor's first dword*/
#define UHCI_INLINK_DSCR_BF0 0xFFFFFFFF
#define UHCI_INLINK_DSCR_BF0_M ((UHCI_INLINK_DSCR_BF0_V)<<(UHCI_INLINK_DSCR_BF0_S))
#define UHCI_INLINK_DSCR_BF0_V 0xFFFFFFFF
#define UHCI_INLINK_DSCR_BF0_S 0
#define UHCI_DMA_IN_DSCR_BF1_REG(i) (REG_UHCI_BASE(i) + 0x54)
/* UHCI_INLINK_DSCR_BF1 : RO ;bitpos:[31:0] ;default: 32'b0 ; */
/*description: The content of current in link descriptor's second dword*/
#define UHCI_INLINK_DSCR_BF1 0xFFFFFFFF
#define UHCI_INLINK_DSCR_BF1_M ((UHCI_INLINK_DSCR_BF1_V)<<(UHCI_INLINK_DSCR_BF1_S))
#define UHCI_INLINK_DSCR_BF1_V 0xFFFFFFFF
#define UHCI_INLINK_DSCR_BF1_S 0
#define UHCI_DMA_OUT_DSCR_REG(i) (REG_UHCI_BASE(i) + 0x58)
/* UHCI_OUTLINK_DSCR : RO ;bitpos:[31:0] ;default: 32'b0 ; */
/*description: The content of current out link descriptor's third dword*/
#define UHCI_OUTLINK_DSCR 0xFFFFFFFF
#define UHCI_OUTLINK_DSCR_M ((UHCI_OUTLINK_DSCR_V)<<(UHCI_OUTLINK_DSCR_S))
#define UHCI_OUTLINK_DSCR_V 0xFFFFFFFF
#define UHCI_OUTLINK_DSCR_S 0
#define UHCI_DMA_OUT_DSCR_BF0_REG(i) (REG_UHCI_BASE(i) + 0x5C)
/* UHCI_OUTLINK_DSCR_BF0 : RO ;bitpos:[31:0] ;default: 32'b0 ; */
/*description: The content of current out link descriptor's first dword*/
#define UHCI_OUTLINK_DSCR_BF0 0xFFFFFFFF
#define UHCI_OUTLINK_DSCR_BF0_M ((UHCI_OUTLINK_DSCR_BF0_V)<<(UHCI_OUTLINK_DSCR_BF0_S))
#define UHCI_OUTLINK_DSCR_BF0_V 0xFFFFFFFF
#define UHCI_OUTLINK_DSCR_BF0_S 0
#define UHCI_DMA_OUT_DSCR_BF1_REG(i) (REG_UHCI_BASE(i) + 0x60)
/* UHCI_OUTLINK_DSCR_BF1 : RO ;bitpos:[31:0] ;default: 32'b0 ; */
/*description: The content of current out link descriptor's second dword*/
#define UHCI_OUTLINK_DSCR_BF1 0xFFFFFFFF
#define UHCI_OUTLINK_DSCR_BF1_M ((UHCI_OUTLINK_DSCR_BF1_V)<<(UHCI_OUTLINK_DSCR_BF1_S))
#define UHCI_OUTLINK_DSCR_BF1_V 0xFFFFFFFF
#define UHCI_OUTLINK_DSCR_BF1_S 0
#define UHCI_ESCAPE_CONF_REG(i) (REG_UHCI_BASE(i) + 0x64)
/* UHCI_RX_13_ESC_EN : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: Set this bit to enable flow control char 0x13 replace when DMA sends data.*/
#define UHCI_RX_13_ESC_EN (BIT(7))
#define UHCI_RX_13_ESC_EN_M (BIT(7))
#define UHCI_RX_13_ESC_EN_V 0x1
#define UHCI_RX_13_ESC_EN_S 7
/* UHCI_RX_11_ESC_EN : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to enable flow control char 0x11 replace when DMA sends data.*/
#define UHCI_RX_11_ESC_EN (BIT(6))
#define UHCI_RX_11_ESC_EN_M (BIT(6))
#define UHCI_RX_11_ESC_EN_V 0x1
#define UHCI_RX_11_ESC_EN_S 6
/* UHCI_RX_DB_ESC_EN : R/W ;bitpos:[5] ;default: 1'b1 ; */
/*description: Set this bit to enable 0xdb char replace when DMA sends data.*/
#define UHCI_RX_DB_ESC_EN (BIT(5))
#define UHCI_RX_DB_ESC_EN_M (BIT(5))
#define UHCI_RX_DB_ESC_EN_V 0x1
#define UHCI_RX_DB_ESC_EN_S 5
/* UHCI_RX_C0_ESC_EN : R/W ;bitpos:[4] ;default: 1'b1 ; */
/*description: Set this bit to enable 0xc0 char replace when DMA sends data.*/
#define UHCI_RX_C0_ESC_EN (BIT(4))
#define UHCI_RX_C0_ESC_EN_M (BIT(4))
#define UHCI_RX_C0_ESC_EN_V 0x1
#define UHCI_RX_C0_ESC_EN_S 4
/* UHCI_TX_13_ESC_EN : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to enable flow control char 0x13 decode when DMA receives data.*/
#define UHCI_TX_13_ESC_EN (BIT(3))
#define UHCI_TX_13_ESC_EN_M (BIT(3))
#define UHCI_TX_13_ESC_EN_V 0x1
#define UHCI_TX_13_ESC_EN_S 3
/* UHCI_TX_11_ESC_EN : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: Set this bit to enable flow control char 0x11 decode when DMA receives data.*/
#define UHCI_TX_11_ESC_EN (BIT(2))
#define UHCI_TX_11_ESC_EN_M (BIT(2))
#define UHCI_TX_11_ESC_EN_V 0x1
#define UHCI_TX_11_ESC_EN_S 2
/* UHCI_TX_DB_ESC_EN : R/W ;bitpos:[1] ;default: 1'b1 ; */
/*description: Set this bit to enable 0xdb char decode when DMA receives data.*/
#define UHCI_TX_DB_ESC_EN (BIT(1))
#define UHCI_TX_DB_ESC_EN_M (BIT(1))
#define UHCI_TX_DB_ESC_EN_V 0x1
#define UHCI_TX_DB_ESC_EN_S 1
/* UHCI_TX_C0_ESC_EN : R/W ;bitpos:[0] ;default: 1'b1 ; */
/*description: Set this bit to enable 0xc0 char decode when DMA receives data.*/
#define UHCI_TX_C0_ESC_EN (BIT(0))
#define UHCI_TX_C0_ESC_EN_M (BIT(0))
#define UHCI_TX_C0_ESC_EN_V 0x1
#define UHCI_TX_C0_ESC_EN_S 0
#define UHCI_HUNG_CONF_REG(i) (REG_UHCI_BASE(i) + 0x68)
/* UHCI_RXFIFO_TIMEOUT_ENA : R/W ;bitpos:[23] ;default: 1'b1 ; */
/*description: This is the enable bit for DMA send data timeout*/
#define UHCI_RXFIFO_TIMEOUT_ENA (BIT(23))
#define UHCI_RXFIFO_TIMEOUT_ENA_M (BIT(23))
#define UHCI_RXFIFO_TIMEOUT_ENA_V 0x1
#define UHCI_RXFIFO_TIMEOUT_ENA_S 23
/* UHCI_RXFIFO_TIMEOUT_SHIFT : R/W ;bitpos:[22:20] ;default: 3'b0 ; */
/*description: The tick count is cleared when its value >=(17'd8000>>reg_rxfifo_timeout_shift)*/
#define UHCI_RXFIFO_TIMEOUT_SHIFT 0x00000007
#define UHCI_RXFIFO_TIMEOUT_SHIFT_M ((UHCI_RXFIFO_TIMEOUT_SHIFT_V)<<(UHCI_RXFIFO_TIMEOUT_SHIFT_S))
#define UHCI_RXFIFO_TIMEOUT_SHIFT_V 0x7
#define UHCI_RXFIFO_TIMEOUT_SHIFT_S 20
/* UHCI_RXFIFO_TIMEOUT : R/W ;bitpos:[19:12] ;default: 8'h10 ; */
/*description: This register stores the timeout value.when DMA takes more time
than this register value to read a data from RAM it will produce uhci_rx_hung_int interrupt.*/
#define UHCI_RXFIFO_TIMEOUT 0x000000FF
#define UHCI_RXFIFO_TIMEOUT_M ((UHCI_RXFIFO_TIMEOUT_V)<<(UHCI_RXFIFO_TIMEOUT_S))
#define UHCI_RXFIFO_TIMEOUT_V 0xFF
#define UHCI_RXFIFO_TIMEOUT_S 12
/* UHCI_TXFIFO_TIMEOUT_ENA : R/W ;bitpos:[11] ;default: 1'b1 ; */
/*description: The enable bit for txfifo receive data timeout*/
#define UHCI_TXFIFO_TIMEOUT_ENA (BIT(11))
#define UHCI_TXFIFO_TIMEOUT_ENA_M (BIT(11))
#define UHCI_TXFIFO_TIMEOUT_ENA_V 0x1
#define UHCI_TXFIFO_TIMEOUT_ENA_S 11
/* UHCI_TXFIFO_TIMEOUT_SHIFT : R/W ;bitpos:[10:8] ;default: 3'b0 ; */
/*description: The tick count is cleared when its value >=(17'd8000>>reg_txfifo_timeout_shift)*/
#define UHCI_TXFIFO_TIMEOUT_SHIFT 0x00000007
#define UHCI_TXFIFO_TIMEOUT_SHIFT_M ((UHCI_TXFIFO_TIMEOUT_SHIFT_V)<<(UHCI_TXFIFO_TIMEOUT_SHIFT_S))
#define UHCI_TXFIFO_TIMEOUT_SHIFT_V 0x7
#define UHCI_TXFIFO_TIMEOUT_SHIFT_S 8
/* UHCI_TXFIFO_TIMEOUT : R/W ;bitpos:[7:0] ;default: 8'h10 ; */
/*description: This register stores the timeout value.when DMA takes more time
than this register value to receive a data it will produce uhci_tx_hung_int interrupt.*/
#define UHCI_TXFIFO_TIMEOUT 0x000000FF
#define UHCI_TXFIFO_TIMEOUT_M ((UHCI_TXFIFO_TIMEOUT_V)<<(UHCI_TXFIFO_TIMEOUT_S))
#define UHCI_TXFIFO_TIMEOUT_V 0xFF
#define UHCI_TXFIFO_TIMEOUT_S 0
#define UHCI_ACK_NUM_REG(i) (REG_UHCI_BASE(i) + 0x6C)
#define UHCI_RX_HEAD_REG(i) (REG_UHCI_BASE(i) + 0x70)
/* UHCI_RX_HEAD : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the packet header received by DMA*/
#define UHCI_RX_HEAD 0xFFFFFFFF
#define UHCI_RX_HEAD_M ((UHCI_RX_HEAD_V)<<(UHCI_RX_HEAD_S))
#define UHCI_RX_HEAD_V 0xFFFFFFFF
#define UHCI_RX_HEAD_S 0
#define UHCI_QUICK_SENT_REG(i) (REG_UHCI_BASE(i) + 0x74)
/* UHCI_ALWAYS_SEND_EN : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: Set this bit to enable continuously send the same short packet*/
#define UHCI_ALWAYS_SEND_EN (BIT(7))
#define UHCI_ALWAYS_SEND_EN_M (BIT(7))
#define UHCI_ALWAYS_SEND_EN_V 0x1
#define UHCI_ALWAYS_SEND_EN_S 7
/* UHCI_ALWAYS_SEND_NUM : R/W ;bitpos:[6:4] ;default: 3'h0 ; */
/*description: The bits are used to choose which short packet*/
#define UHCI_ALWAYS_SEND_NUM 0x00000007
#define UHCI_ALWAYS_SEND_NUM_M ((UHCI_ALWAYS_SEND_NUM_V)<<(UHCI_ALWAYS_SEND_NUM_S))
#define UHCI_ALWAYS_SEND_NUM_V 0x7
#define UHCI_ALWAYS_SEND_NUM_S 4
/* UHCI_SINGLE_SEND_EN : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to enable send a short packet*/
#define UHCI_SINGLE_SEND_EN (BIT(3))
#define UHCI_SINGLE_SEND_EN_M (BIT(3))
#define UHCI_SINGLE_SEND_EN_V 0x1
#define UHCI_SINGLE_SEND_EN_S 3
/* UHCI_SINGLE_SEND_NUM : R/W ;bitpos:[2:0] ;default: 3'h0 ; */
/*description: The bits are used to choose which short packet*/
#define UHCI_SINGLE_SEND_NUM 0x00000007
#define UHCI_SINGLE_SEND_NUM_M ((UHCI_SINGLE_SEND_NUM_V)<<(UHCI_SINGLE_SEND_NUM_S))
#define UHCI_SINGLE_SEND_NUM_V 0x7
#define UHCI_SINGLE_SEND_NUM_S 0
#define UHCI_Q0_WORD0_REG(i) (REG_UHCI_BASE(i) + 0x78)
/* UHCI_SEND_Q0_WORD0 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's first dword*/
#define UHCI_SEND_Q0_WORD0 0xFFFFFFFF
#define UHCI_SEND_Q0_WORD0_M ((UHCI_SEND_Q0_WORD0_V)<<(UHCI_SEND_Q0_WORD0_S))
#define UHCI_SEND_Q0_WORD0_V 0xFFFFFFFF
#define UHCI_SEND_Q0_WORD0_S 0
#define UHCI_Q0_WORD1_REG(i) (REG_UHCI_BASE(i) + 0x7C)
/* UHCI_SEND_Q0_WORD1 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's second dword*/
#define UHCI_SEND_Q0_WORD1 0xFFFFFFFF
#define UHCI_SEND_Q0_WORD1_M ((UHCI_SEND_Q0_WORD1_V)<<(UHCI_SEND_Q0_WORD1_S))
#define UHCI_SEND_Q0_WORD1_V 0xFFFFFFFF
#define UHCI_SEND_Q0_WORD1_S 0
#define UHCI_Q1_WORD0_REG(i) (REG_UHCI_BASE(i) + 0x80)
/* UHCI_SEND_Q1_WORD0 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's first dword*/
#define UHCI_SEND_Q1_WORD0 0xFFFFFFFF
#define UHCI_SEND_Q1_WORD0_M ((UHCI_SEND_Q1_WORD0_V)<<(UHCI_SEND_Q1_WORD0_S))
#define UHCI_SEND_Q1_WORD0_V 0xFFFFFFFF
#define UHCI_SEND_Q1_WORD0_S 0
#define UHCI_Q1_WORD1_REG(i) (REG_UHCI_BASE(i) + 0x84)
/* UHCI_SEND_Q1_WORD1 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's second dword*/
#define UHCI_SEND_Q1_WORD1 0xFFFFFFFF
#define UHCI_SEND_Q1_WORD1_M ((UHCI_SEND_Q1_WORD1_V)<<(UHCI_SEND_Q1_WORD1_S))
#define UHCI_SEND_Q1_WORD1_V 0xFFFFFFFF
#define UHCI_SEND_Q1_WORD1_S 0
#define UHCI_Q2_WORD0_REG(i) (REG_UHCI_BASE(i) + 0x88)
/* UHCI_SEND_Q2_WORD0 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's first dword*/
#define UHCI_SEND_Q2_WORD0 0xFFFFFFFF
#define UHCI_SEND_Q2_WORD0_M ((UHCI_SEND_Q2_WORD0_V)<<(UHCI_SEND_Q2_WORD0_S))
#define UHCI_SEND_Q2_WORD0_V 0xFFFFFFFF
#define UHCI_SEND_Q2_WORD0_S 0
#define UHCI_Q2_WORD1_REG(i) (REG_UHCI_BASE(i) + 0x8C)
/* UHCI_SEND_Q2_WORD1 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's second dword*/
#define UHCI_SEND_Q2_WORD1 0xFFFFFFFF
#define UHCI_SEND_Q2_WORD1_M ((UHCI_SEND_Q2_WORD1_V)<<(UHCI_SEND_Q2_WORD1_S))
#define UHCI_SEND_Q2_WORD1_V 0xFFFFFFFF
#define UHCI_SEND_Q2_WORD1_S 0
#define UHCI_Q3_WORD0_REG(i) (REG_UHCI_BASE(i) + 0x90)
/* UHCI_SEND_Q3_WORD0 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's first dword*/
#define UHCI_SEND_Q3_WORD0 0xFFFFFFFF
#define UHCI_SEND_Q3_WORD0_M ((UHCI_SEND_Q3_WORD0_V)<<(UHCI_SEND_Q3_WORD0_S))
#define UHCI_SEND_Q3_WORD0_V 0xFFFFFFFF
#define UHCI_SEND_Q3_WORD0_S 0
#define UHCI_Q3_WORD1_REG(i) (REG_UHCI_BASE(i) + 0x94)
/* UHCI_SEND_Q3_WORD1 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's second dword*/
#define UHCI_SEND_Q3_WORD1 0xFFFFFFFF
#define UHCI_SEND_Q3_WORD1_M ((UHCI_SEND_Q3_WORD1_V)<<(UHCI_SEND_Q3_WORD1_S))
#define UHCI_SEND_Q3_WORD1_V 0xFFFFFFFF
#define UHCI_SEND_Q3_WORD1_S 0
#define UHCI_Q4_WORD0_REG(i) (REG_UHCI_BASE(i) + 0x98)
/* UHCI_SEND_Q4_WORD0 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's first dword*/
#define UHCI_SEND_Q4_WORD0 0xFFFFFFFF
#define UHCI_SEND_Q4_WORD0_M ((UHCI_SEND_Q4_WORD0_V)<<(UHCI_SEND_Q4_WORD0_S))
#define UHCI_SEND_Q4_WORD0_V 0xFFFFFFFF
#define UHCI_SEND_Q4_WORD0_S 0
#define UHCI_Q4_WORD1_REG(i) (REG_UHCI_BASE(i) + 0x9C)
/* UHCI_SEND_Q4_WORD1 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's second dword*/
#define UHCI_SEND_Q4_WORD1 0xFFFFFFFF
#define UHCI_SEND_Q4_WORD1_M ((UHCI_SEND_Q4_WORD1_V)<<(UHCI_SEND_Q4_WORD1_S))
#define UHCI_SEND_Q4_WORD1_V 0xFFFFFFFF
#define UHCI_SEND_Q4_WORD1_S 0
#define UHCI_Q5_WORD0_REG(i) (REG_UHCI_BASE(i) + 0xA0)
/* UHCI_SEND_Q5_WORD0 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's first dword*/
#define UHCI_SEND_Q5_WORD0 0xFFFFFFFF
#define UHCI_SEND_Q5_WORD0_M ((UHCI_SEND_Q5_WORD0_V)<<(UHCI_SEND_Q5_WORD0_S))
#define UHCI_SEND_Q5_WORD0_V 0xFFFFFFFF
#define UHCI_SEND_Q5_WORD0_S 0
#define UHCI_Q5_WORD1_REG(i) (REG_UHCI_BASE(i) + 0xA4)
/* UHCI_SEND_Q5_WORD1 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's second dword*/
#define UHCI_SEND_Q5_WORD1 0xFFFFFFFF
#define UHCI_SEND_Q5_WORD1_M ((UHCI_SEND_Q5_WORD1_V)<<(UHCI_SEND_Q5_WORD1_S))
#define UHCI_SEND_Q5_WORD1_V 0xFFFFFFFF
#define UHCI_SEND_Q5_WORD1_S 0
#define UHCI_Q6_WORD0_REG(i) (REG_UHCI_BASE(i) + 0xA8)
/* UHCI_SEND_Q6_WORD0 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's first dword*/
#define UHCI_SEND_Q6_WORD0 0xFFFFFFFF
#define UHCI_SEND_Q6_WORD0_M ((UHCI_SEND_Q6_WORD0_V)<<(UHCI_SEND_Q6_WORD0_S))
#define UHCI_SEND_Q6_WORD0_V 0xFFFFFFFF
#define UHCI_SEND_Q6_WORD0_S 0
#define UHCI_Q6_WORD1_REG(i) (REG_UHCI_BASE(i) + 0xAC)
/* UHCI_SEND_Q6_WORD1 : R/W ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: This register stores the content of short packet's second dword*/
#define UHCI_SEND_Q6_WORD1 0xFFFFFFFF
#define UHCI_SEND_Q6_WORD1_M ((UHCI_SEND_Q6_WORD1_V)<<(UHCI_SEND_Q6_WORD1_S))
#define UHCI_SEND_Q6_WORD1_V 0xFFFFFFFF
#define UHCI_SEND_Q6_WORD1_S 0
#define UHCI_ESC_CONF0_REG(i) (REG_UHCI_BASE(i) + 0xB0)
/* UHCI_SEPER_ESC_CHAR1 : R/W ;bitpos:[23:16] ;default: 8'hdc ; */
/*description: This register stores the second char used to replace seperator
char in data . 0xdc 0xdb replace 0xc0 by default.*/
#define UHCI_SEPER_ESC_CHAR1 0x000000FF
#define UHCI_SEPER_ESC_CHAR1_M ((UHCI_SEPER_ESC_CHAR1_V)<<(UHCI_SEPER_ESC_CHAR1_S))
#define UHCI_SEPER_ESC_CHAR1_V 0xFF
#define UHCI_SEPER_ESC_CHAR1_S 16
/* UHCI_SEPER_ESC_CHAR0 : R/W ;bitpos:[15:8] ;default: 8'hdb ; */
/*description: This register stores thee first char used to replace seperator char in data.*/
#define UHCI_SEPER_ESC_CHAR0 0x000000FF
#define UHCI_SEPER_ESC_CHAR0_M ((UHCI_SEPER_ESC_CHAR0_V)<<(UHCI_SEPER_ESC_CHAR0_S))
#define UHCI_SEPER_ESC_CHAR0_V 0xFF
#define UHCI_SEPER_ESC_CHAR0_S 8
/* UHCI_SEPER_CHAR : R/W ;bitpos:[7:0] ;default: 8'hc0 ; */
/*description: This register stores the seperator char seperator char is used
to seperate the data frame.*/
#define UHCI_SEPER_CHAR 0x000000FF
#define UHCI_SEPER_CHAR_M ((UHCI_SEPER_CHAR_V)<<(UHCI_SEPER_CHAR_S))
#define UHCI_SEPER_CHAR_V 0xFF
#define UHCI_SEPER_CHAR_S 0
#define UHCI_ESC_CONF1_REG(i) (REG_UHCI_BASE(i) + 0xB4)
/* UHCI_ESC_SEQ0_CHAR1 : R/W ;bitpos:[23:16] ;default: 8'hdd ; */
/*description: This register stores the second char used to replace the reg_esc_seq0 in data*/
#define UHCI_ESC_SEQ0_CHAR1 0x000000FF
#define UHCI_ESC_SEQ0_CHAR1_M ((UHCI_ESC_SEQ0_CHAR1_V)<<(UHCI_ESC_SEQ0_CHAR1_S))
#define UHCI_ESC_SEQ0_CHAR1_V 0xFF
#define UHCI_ESC_SEQ0_CHAR1_S 16
/* UHCI_ESC_SEQ0_CHAR0 : R/W ;bitpos:[15:8] ;default: 8'hdb ; */
/*description: This register stores the first char used to replace reg_esc_seq0 in data.*/
#define UHCI_ESC_SEQ0_CHAR0 0x000000FF
#define UHCI_ESC_SEQ0_CHAR0_M ((UHCI_ESC_SEQ0_CHAR0_V)<<(UHCI_ESC_SEQ0_CHAR0_S))
#define UHCI_ESC_SEQ0_CHAR0_V 0xFF
#define UHCI_ESC_SEQ0_CHAR0_S 8
/* UHCI_ESC_SEQ0 : R/W ;bitpos:[7:0] ;default: 8'hdb ; */
/*description: This register stores the first substitute char used to replace
the seperator char.*/
#define UHCI_ESC_SEQ0 0x000000FF
#define UHCI_ESC_SEQ0_M ((UHCI_ESC_SEQ0_V)<<(UHCI_ESC_SEQ0_S))
#define UHCI_ESC_SEQ0_V 0xFF
#define UHCI_ESC_SEQ0_S 0
#define UHCI_ESC_CONF2_REG(i) (REG_UHCI_BASE(i) + 0xB8)
/* UHCI_ESC_SEQ1_CHAR1 : R/W ;bitpos:[23:16] ;default: 8'hde ; */
/*description: This register stores the second char used to replace the reg_esc_seq1 in data.*/
#define UHCI_ESC_SEQ1_CHAR1 0x000000FF
#define UHCI_ESC_SEQ1_CHAR1_M ((UHCI_ESC_SEQ1_CHAR1_V)<<(UHCI_ESC_SEQ1_CHAR1_S))
#define UHCI_ESC_SEQ1_CHAR1_V 0xFF
#define UHCI_ESC_SEQ1_CHAR1_S 16
/* UHCI_ESC_SEQ1_CHAR0 : R/W ;bitpos:[15:8] ;default: 8'hdb ; */
/*description: This register stores the first char used to replace the reg_esc_seq1 in data.*/
#define UHCI_ESC_SEQ1_CHAR0 0x000000FF
#define UHCI_ESC_SEQ1_CHAR0_M ((UHCI_ESC_SEQ1_CHAR0_V)<<(UHCI_ESC_SEQ1_CHAR0_S))
#define UHCI_ESC_SEQ1_CHAR0_V 0xFF
#define UHCI_ESC_SEQ1_CHAR0_S 8
/* UHCI_ESC_SEQ1 : R/W ;bitpos:[7:0] ;default: 8'h11 ; */
/*description: This register stores the flow control char to turn on the flow_control*/
#define UHCI_ESC_SEQ1 0x000000FF
#define UHCI_ESC_SEQ1_M ((UHCI_ESC_SEQ1_V)<<(UHCI_ESC_SEQ1_S))
#define UHCI_ESC_SEQ1_V 0xFF
#define UHCI_ESC_SEQ1_S 0
#define UHCI_ESC_CONF3_REG(i) (REG_UHCI_BASE(i) + 0xBC)
/* UHCI_ESC_SEQ2_CHAR1 : R/W ;bitpos:[23:16] ;default: 8'hdf ; */
/*description: This register stores the second char used to replace the reg_esc_seq2 in data.*/
#define UHCI_ESC_SEQ2_CHAR1 0x000000FF
#define UHCI_ESC_SEQ2_CHAR1_M ((UHCI_ESC_SEQ2_CHAR1_V)<<(UHCI_ESC_SEQ2_CHAR1_S))
#define UHCI_ESC_SEQ2_CHAR1_V 0xFF
#define UHCI_ESC_SEQ2_CHAR1_S 16
/* UHCI_ESC_SEQ2_CHAR0 : R/W ;bitpos:[15:8] ;default: 8'hdb ; */
/*description: This register stores the first char used to replace the reg_esc_seq2 in data.*/
#define UHCI_ESC_SEQ2_CHAR0 0x000000FF
#define UHCI_ESC_SEQ2_CHAR0_M ((UHCI_ESC_SEQ2_CHAR0_V)<<(UHCI_ESC_SEQ2_CHAR0_S))
#define UHCI_ESC_SEQ2_CHAR0_V 0xFF
#define UHCI_ESC_SEQ2_CHAR0_S 8
/* UHCI_ESC_SEQ2 : R/W ;bitpos:[7:0] ;default: 8'h13 ; */
/*description: This register stores the flow_control char to turn off the flow_control*/
#define UHCI_ESC_SEQ2 0x000000FF
#define UHCI_ESC_SEQ2_M ((UHCI_ESC_SEQ2_V)<<(UHCI_ESC_SEQ2_S))
#define UHCI_ESC_SEQ2_V 0xFF
#define UHCI_ESC_SEQ2_S 0
#define UHCI_PKT_THRES_REG(i) (REG_UHCI_BASE(i) + 0xC0)
/* UHCI_PKT_THRS : R/W ;bitpos:[12:0] ;default: 13'h80 ; */
/*description: when the amount of packet payload is greater than this value
the process of receiving data is done.*/
#define UHCI_PKT_THRS 0x00001FFF
#define UHCI_PKT_THRS_M ((UHCI_PKT_THRS_V)<<(UHCI_PKT_THRS_S))
#define UHCI_PKT_THRS_V 0x1FFF
#define UHCI_PKT_THRS_S 0
#define UHCI_DATE_REG(i) (REG_UHCI_BASE(i) + 0xFC)
/* UHCI_DATE : R/W ;bitpos:[31:0] ;default: 32'h16041001 ; */
/*description: version information*/
#define UHCI_DATE 0xFFFFFFFF
#define UHCI_DATE_M ((UHCI_DATE_V)<<(UHCI_DATE_S))
#define UHCI_DATE_V 0xFFFFFFFF
#define UHCI_DATE_S 0
#endif /*_SOC_UHCI_REG_H_ */