jacob.eva/arduino-esp32
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
fd81fd0ac3
arduino-esp32/tools/sdk/include/driver/driver/gpio.h
me-no-dev 1d759380a6 Major IDF and Arduino Update 
WiFi and BlueTooth can now be started and stopped at will.
basic functions added to esp32-hal to start and stop the BT radio
SimpleBLE class added to show the most basic functionality
Example to show how to switch between BT, WiFi or Both
2017-02-23 01:11:57 +02:00

476 lines
19 KiB
C
Raw Blame History

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#ifndef _DRIVER_GPIO_H_
#define _DRIVER_GPIO_H_
#include "esp_err.h"
#include <esp_types.h>
#include "soc/gpio_reg.h"
#include "soc/gpio_struct.h"
#include "soc/rtc_io_reg.h"
#include "soc/io_mux_reg.h"
#include "soc/gpio_sig_map.h"
#include "rom/gpio.h"
#include "esp_attr.h"
#include "esp_intr_alloc.h"
#ifdef __cplusplus
extern "C" {
#endif
#define GPIO_SEL_0 (BIT(0)) /*!< Pin 0 selected */
#define GPIO_SEL_1 (BIT(1)) /*!< Pin 1 selected */
#define GPIO_SEL_2 (BIT(2)) /*!< Pin 2 selected */
#define GPIO_SEL_3 (BIT(3)) /*!< Pin 3 selected */
#define GPIO_SEL_4 (BIT(4)) /*!< Pin 4 selected */
#define GPIO_SEL_5 (BIT(5)) /*!< Pin 5 selected */
#define GPIO_SEL_6 (BIT(6)) /*!< Pin 6 selected */
#define GPIO_SEL_7 (BIT(7)) /*!< Pin 7 selected */
#define GPIO_SEL_8 (BIT(8)) /*!< Pin 8 selected */
#define GPIO_SEL_9 (BIT(9)) /*!< Pin 9 selected */
#define GPIO_SEL_10 (BIT(10)) /*!< Pin 10 selected */
#define GPIO_SEL_11 (BIT(11)) /*!< Pin 11 selected */
#define GPIO_SEL_12 (BIT(12)) /*!< Pin 12 selected */
#define GPIO_SEL_13 (BIT(13)) /*!< Pin 13 selected */
#define GPIO_SEL_14 (BIT(14)) /*!< Pin 14 selected */
#define GPIO_SEL_15 (BIT(15)) /*!< Pin 15 selected */
#define GPIO_SEL_16 (BIT(16)) /*!< Pin 16 selected */
#define GPIO_SEL_17 (BIT(17)) /*!< Pin 17 selected */
#define GPIO_SEL_18 (BIT(18)) /*!< Pin 18 selected */
#define GPIO_SEL_19 (BIT(19)) /*!< Pin 19 selected */
#define GPIO_SEL_21 (BIT(21)) /*!< Pin 21 selected */
#define GPIO_SEL_22 (BIT(22)) /*!< Pin 22 selected */
#define GPIO_SEL_23 (BIT(23)) /*!< Pin 23 selected */
#define GPIO_SEL_25 (BIT(25)) /*!< Pin 25 selected */
#define GPIO_SEL_26 (BIT(26)) /*!< Pin 26 selected */
#define GPIO_SEL_27 (BIT(27)) /*!< Pin 27 selected */
#define GPIO_SEL_32 ((uint64_t)(((uint64_t)1)<<32)) /*!< Pin 32 selected */
#define GPIO_SEL_33 ((uint64_t)(((uint64_t)1)<<33)) /*!< Pin 33 selected */
#define GPIO_SEL_34 ((uint64_t)(((uint64_t)1)<<34)) /*!< Pin 34 selected */
#define GPIO_SEL_35 ((uint64_t)(((uint64_t)1)<<35)) /*!< Pin 35 selected */
#define GPIO_SEL_36 ((uint64_t)(((uint64_t)1)<<36)) /*!< Pin 36 selected */
#define GPIO_SEL_37 ((uint64_t)(((uint64_t)1)<<37)) /*!< Pin 37 selected */
#define GPIO_SEL_38 ((uint64_t)(((uint64_t)1)<<38)) /*!< Pin 38 selected */
#define GPIO_SEL_39 ((uint64_t)(((uint64_t)1)<<39)) /*!< Pin 39 selected */
#define GPIO_PIN_REG_0 PERIPHS_IO_MUX_GPIO0_U
#define GPIO_PIN_REG_1 PERIPHS_IO_MUX_U0TXD_U
#define GPIO_PIN_REG_2 PERIPHS_IO_MUX_GPIO2_U
#define GPIO_PIN_REG_3 PERIPHS_IO_MUX_U0RXD_U
#define GPIO_PIN_REG_4 PERIPHS_IO_MUX_GPIO4_U
#define GPIO_PIN_REG_5 PERIPHS_IO_MUX_GPIO5_U
#define GPIO_PIN_REG_6 PERIPHS_IO_MUX_SD_CLK_U
#define GPIO_PIN_REG_7 PERIPHS_IO_MUX_SD_DATA0_U
#define GPIO_PIN_REG_8 PERIPHS_IO_MUX_SD_DATA1_U
#define GPIO_PIN_REG_9 PERIPHS_IO_MUX_SD_DATA2_U
#define GPIO_PIN_REG_10 PERIPHS_IO_MUX_SD_DATA3_U
#define GPIO_PIN_REG_11 PERIPHS_IO_MUX_SD_CMD_U
#define GPIO_PIN_REG_12 PERIPHS_IO_MUX_MTDI_U
#define GPIO_PIN_REG_13 PERIPHS_IO_MUX_MTCK_U
#define GPIO_PIN_REG_14 PERIPHS_IO_MUX_MTMS_U
#define GPIO_PIN_REG_15 PERIPHS_IO_MUX_MTDO_U
#define GPIO_PIN_REG_16 PERIPHS_IO_MUX_GPIO16_U
#define GPIO_PIN_REG_17 PERIPHS_IO_MUX_GPIO17_U
#define GPIO_PIN_REG_18 PERIPHS_IO_MUX_GPIO18_U
#define GPIO_PIN_REG_19 PERIPHS_IO_MUX_GPIO19_U
#define GPIO_PIN_REG_20 PERIPHS_IO_MUX_GPIO20_U
#define GPIO_PIN_REG_21 PERIPHS_IO_MUX_GPIO21_U
#define GPIO_PIN_REG_22 PERIPHS_IO_MUX_GPIO22_U
#define GPIO_PIN_REG_23 PERIPHS_IO_MUX_GPIO23_U
#define GPIO_PIN_REG_25 PERIPHS_IO_MUX_GPIO25_U
#define GPIO_PIN_REG_26 PERIPHS_IO_MUX_GPIO26_U
#define GPIO_PIN_REG_27 PERIPHS_IO_MUX_GPIO27_U
#define GPIO_PIN_REG_32 PERIPHS_IO_MUX_GPIO32_U
#define GPIO_PIN_REG_33 PERIPHS_IO_MUX_GPIO33_U
#define GPIO_PIN_REG_34 PERIPHS_IO_MUX_GPIO34_U
#define GPIO_PIN_REG_35 PERIPHS_IO_MUX_GPIO35_U
#define GPIO_PIN_REG_36 PERIPHS_IO_MUX_GPIO36_U
#define GPIO_PIN_REG_37 PERIPHS_IO_MUX_GPIO37_U
#define GPIO_PIN_REG_38 PERIPHS_IO_MUX_GPIO38_U
#define GPIO_PIN_REG_39 PERIPHS_IO_MUX_GPIO39_U
#define GPIO_APP_CPU_INTR_ENA (BIT(0))
#define GPIO_APP_CPU_NMI_INTR_ENA (BIT(1))
#define GPIO_PRO_CPU_INTR_ENA (BIT(2))
#define GPIO_PRO_CPU_NMI_INTR_ENA (BIT(3))
#define GPIO_SDIO_EXT_INTR_ENA (BIT(4))
#define GPIO_MODE_DEF_INPUT (BIT0)
#define GPIO_MODE_DEF_OUTPUT (BIT1)
#define GPIO_MODE_DEF_OD (BIT2)
#define GPIO_PIN_COUNT 40
extern const uint32_t GPIO_PIN_MUX_REG[GPIO_PIN_COUNT];
#define GPIO_IS_VALID_GPIO(gpio_num) ((gpio_num < GPIO_PIN_COUNT && GPIO_PIN_MUX_REG[gpio_num] != 0)) //to decide whether it is a valid GPIO number
#define GPIO_IS_VALID_OUTPUT_GPIO(gpio_num) ((GPIO_IS_VALID_GPIO(gpio_num)) && (gpio_num < 34)) //to decide whether it can be a valid GPIO number of output mode
typedef enum {
GPIO_NUM_0 = 0, /*!< GPIO0, input and output */
GPIO_NUM_1 = 1, /*!< GPIO1, input and output */
GPIO_NUM_2 = 2, /*!< GPIO2, input and output */
GPIO_NUM_3 = 3, /*!< GPIO3, input and output */
GPIO_NUM_4 = 4, /*!< GPIO4, input and output */
GPIO_NUM_5 = 5, /*!< GPIO5, input and output */
GPIO_NUM_6 = 6, /*!< GPIO6, input and output */
GPIO_NUM_7 = 7, /*!< GPIO7, input and output */
GPIO_NUM_8 = 8, /*!< GPIO8, input and output */
GPIO_NUM_9 = 9, /*!< GPIO9, input and output */
GPIO_NUM_10 = 10, /*!< GPIO10, input and output */
GPIO_NUM_11 = 11, /*!< GPIO11, input and output */
GPIO_NUM_12 = 12, /*!< GPIO12, input and output */
GPIO_NUM_13 = 13, /*!< GPIO13, input and output */
GPIO_NUM_14 = 14, /*!< GPIO14, input and output */
GPIO_NUM_15 = 15, /*!< GPIO15, input and output */
GPIO_NUM_16 = 16, /*!< GPIO16, input and output */
GPIO_NUM_17 = 17, /*!< GPIO17, input and output */
GPIO_NUM_18 = 18, /*!< GPIO18, input and output */
GPIO_NUM_19 = 19, /*!< GPIO19, input and output */
GPIO_NUM_21 = 21, /*!< GPIO21, input and output */
GPIO_NUM_22 = 22, /*!< GPIO22, input and output */
GPIO_NUM_23 = 23, /*!< GPIO23, input and output */
GPIO_NUM_25 = 25, /*!< GPIO25, input and output */
GPIO_NUM_26 = 26, /*!< GPIO26, input and output */
GPIO_NUM_27 = 27, /*!< GPIO27, input and output */
GPIO_NUM_32 = 32, /*!< GPIO32, input and output */
GPIO_NUM_33 = 33, /*!< GPIO32, input and output */
GPIO_NUM_34 = 34, /*!< GPIO34, input mode only */
GPIO_NUM_35 = 35, /*!< GPIO35, input mode only */
GPIO_NUM_36 = 36, /*!< GPIO36, input mode only */
GPIO_NUM_37 = 37, /*!< GPIO37, input mode only */
GPIO_NUM_38 = 38, /*!< GPIO38, input mode only */
GPIO_NUM_39 = 39, /*!< GPIO39, input mode only */
GPIO_NUM_MAX = 40,
} gpio_num_t;
typedef enum {
GPIO_INTR_DISABLE = 0, /*!< Disable GPIO interrupt */
GPIO_INTR_POSEDGE = 1, /*!< GPIO interrupt type : rising edge */
GPIO_INTR_NEGEDGE = 2, /*!< GPIO interrupt type : falling edge */
GPIO_INTR_ANYEDGE = 3, /*!< GPIO interrupt type : both rising and falling edge */
GPIO_INTR_LOW_LEVEL = 4, /*!< GPIO interrupt type : input low level trigger */
GPIO_INTR_HIGH_LEVEL = 5, /*!< GPIO interrupt type : input high level trigger */
GPIO_INTR_MAX,
} gpio_int_type_t;
typedef enum {
GPIO_MODE_INPUT = GPIO_MODE_DEF_INPUT, /*!< GPIO mode : input only */
GPIO_MODE_OUTPUT = GPIO_MODE_DEF_OUTPUT, /*!< GPIO mode : output only mode */
GPIO_MODE_OUTPUT_OD = ((GPIO_MODE_DEF_OUTPUT)|(GPIO_MODE_DEF_OD)), /*!< GPIO mode : output only with open-drain mode */
GPIO_MODE_INPUT_OUTPUT_OD = ((GPIO_MODE_DEF_INPUT)|(GPIO_MODE_DEF_OUTPUT)|(GPIO_MODE_DEF_OD)), /*!< GPIO mode : output and input with open-drain mode*/
GPIO_MODE_INPUT_OUTPUT = ((GPIO_MODE_DEF_INPUT)|(GPIO_MODE_DEF_OUTPUT)), /*!< GPIO mode : output and input mode */
} gpio_mode_t;
typedef enum {
GPIO_PULLUP_DISABLE = 0x0, /*!< Disable GPIO pull-up resistor */
GPIO_PULLUP_ENABLE = 0x1, /*!< Enable GPIO pull-up resistor */
} gpio_pullup_t;
typedef enum {
GPIO_PULLDOWN_DISABLE = 0x0, /*!< Disable GPIO pull-down resistor */
GPIO_PULLDOWN_ENABLE = 0x1, /*!< Enable GPIO pull-down resistor */
} gpio_pulldown_t;
/**
* @brief Configuration parameters of GPIO pad for gpio_config function
*/
typedef struct {
uint64_t pin_bit_mask; /*!< GPIO pin: set with bit mask, each bit maps to a GPIO */
gpio_mode_t mode; /*!< GPIO mode: set input/output mode */
gpio_pullup_t pull_up_en; /*!< GPIO pull-up */
gpio_pulldown_t pull_down_en; /*!< GPIO pull-down */
gpio_int_type_t intr_type; /*!< GPIO interrupt type */
} gpio_config_t;
typedef enum {
GPIO_PULLUP_ONLY, /*!< Pad pull up */
GPIO_PULLDOWN_ONLY, /*!< Pad pull down */
GPIO_PULLUP_PULLDOWN, /*!< Pad pull up + pull down*/
GPIO_FLOATING, /*!< Pad floating */
} gpio_pull_mode_t;
typedef void (*gpio_isr_t)(void*);
typedef intr_handle_t gpio_isr_handle_t;
/**
* @brief GPIO common configuration
*
* Configure GPIO's Mode,pull-up,PullDown,IntrType
*
* @param pGPIOConfig Pointer to GPIO configure struct
*
* @return
* - ESP_OK success
* - ESP_ERR_INVALID_ARG Parameter error
*
*/
esp_err_t gpio_config(gpio_config_t *pGPIOConfig);
/**
* @brief GPIO set interrupt trigger type
*
* @param gpio_num GPIO number. If you want to set the trigger type of e.g. of GPIO16, gpio_num should be GPIO_NUM_16 (16);
* @param intr_type Interrupt type, select from gpio_int_type_t
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_ARG Parameter error
*
*/
esp_err_t gpio_set_intr_type(gpio_num_t gpio_num, gpio_int_type_t intr_type);
/**
* @brief Enable GPIO module interrupt signal
*
* @param gpio_num GPIO number. If you want to enable an interrupt on e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_ARG Parameter error
*
*/
esp_err_t gpio_intr_enable(gpio_num_t gpio_num);
/**
* @brief Disable GPIO module interrupt signal
*
* @param gpio_num GPIO number. If you want to disable the interrupt of e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);
*
* @return
* - ESP_OK success
* - ESP_ERR_INVALID_ARG Parameter error
*
*/
esp_err_t gpio_intr_disable(gpio_num_t gpio_num);
/**
* @brief GPIO set output level
*
* @param gpio_num GPIO number. If you want to set the output level of e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);
* @param level Output level. 0: low ; 1: high
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_ARG GPIO number error
*
*/
esp_err_t gpio_set_level(gpio_num_t gpio_num, uint32_t level);
/**
* @brief GPIO get input level
*
* @param gpio_num GPIO number. If you want to get the logic level of e.g. pin GPIO16, gpio_num should be GPIO_NUM_16 (16);
*
* @return
* - 0 the GPIO input level is 0
* - 1 the GPIO input level is 1
*
*/
int gpio_get_level(gpio_num_t gpio_num);
/**
* @brief GPIO set direction
*
* Configure GPIO direction,such as output_only,input_only,output_and_input
*
* @param gpio_num Configure GPIO pins number, it should be GPIO number. If you want to set direction of e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);
* @param mode GPIO direction
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_ARG GPIO error
*
*/
esp_err_t gpio_set_direction(gpio_num_t gpio_num, gpio_mode_t mode);
/**
* @brief Configure GPIO pull-up/pull-down resistors
*
* Only pins that support both input & output have integrated pull-up and pull-down resistors. Input-only GPIOs 34-39 do not.
*
* @param gpio_num GPIO number. If you want to set pull up or down mode for e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);
* @param pull GPIO pull up/down mode.
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_ARG : Parameter error
*
*/
esp_err_t gpio_set_pull_mode(gpio_num_t gpio_num, gpio_pull_mode_t pull);
/**
* @brief Enable GPIO wake-up function.
*
* @param gpio_num GPIO number.
*
* @param intr_type GPIO wake-up type. Only GPIO_INTR_LOW_LEVEL or GPIO_INTR_HIGH_LEVEL can be used.
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_ARG Parameter error
*/
esp_err_t gpio_wakeup_enable(gpio_num_t gpio_num, gpio_int_type_t intr_type);
/**
* @brief Disable GPIO wake-up function.
*
* @param gpio_num GPIO number
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_ARG Parameter error
*/
esp_err_t gpio_wakeup_disable(gpio_num_t gpio_num);
/**
* @brief Register GPIO interrupt handler, the handler is an ISR.
* The handler will be attached to the same CPU core that this function is running on.
*
* This ISR function is called whenever any GPIO interrupt occurs. See
* the alternative gpio_install_isr_service() and
* gpio_isr_handler_add() API in order to have the driver support
* per-GPIO ISRs.
*
* @param fn Interrupt handler function.
* @param intr_alloc_flags Flags used to allocate the interrupt. One or multiple (ORred)
* ESP_INTR_FLAG_* values. See esp_intr_alloc.h for more info.
* @param arg Parameter for handler function
* @param handle Pointer to return handle. If non-NULL, a handle for the interrupt will be returned here.
*
* \verbatim embed:rst:leading-asterisk
* To disable or remove the ISR, pass the returned handle to the :doc:`interrupt allocation functions </api/system/intr_alloc>`.
* \endverbatim
*
* @return
* - ESP_OK Success ;
* - ESP_ERR_INVALID_ARG GPIO error
*/
esp_err_t gpio_isr_register(void (*fn)(void*), void * arg, int intr_alloc_flags, gpio_isr_handle_t *handle);
/**
* @brief Enable pull-up on GPIO.
*
* @param gpio_num GPIO number
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_ARG Parameter error
*/
esp_err_t gpio_pullup_en(gpio_num_t gpio_num);
/**
* @brief Disable pull-up on GPIO.
*
* @param gpio_num GPIO number
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_ARG Parameter error
*/
esp_err_t gpio_pullup_dis(gpio_num_t gpio_num);
/**
* @brief Enable pull-down on GPIO.
*
* @param gpio_num GPIO number
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_ARG Parameter error
*/
esp_err_t gpio_pulldown_en(gpio_num_t gpio_num);
/**
* @brief Disable pull-down on GPIO.
*
* @param gpio_num GPIO number
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_ARG Parameter error
*/
esp_err_t gpio_pulldown_dis(gpio_num_t gpio_num);
/**
* @brief Install the driver's GPIO ISR handler service, which allows per-pin GPIO interrupt handlers.
*
* This function is incompatible with gpio_isr_register() - if that function is used, a single global ISR is registered for all GPIO interrupts. If this function is used, the ISR service provides a global GPIO ISR and individual pin handlers are registered via the gpio_isr_register() function.
*
* @param intr_alloc_flags Flags used to allocate the interrupt. One or multiple (ORred)
* ESP_INTR_FLAG_* values. See esp_intr_alloc.h for more info.
*
* @return
* - ESP_OK Success
* - ESP_FAIL Operation fail
* - ESP_ERR_NO_MEM No memory to install this service
*/
esp_err_t gpio_install_isr_service(int intr_alloc_flags);
/**
* @brief Uninstall the driver's GPIO ISR service, freeing related resources.
*/
void gpio_uninstall_isr_service();
/**
* @brief Add ISR handler for the corresponding GPIO pin.
*
* Call this function after using gpio_install_isr_service() to
* install the driver's GPIO ISR handler service.
*
* The pin ISR handlers no longer need to be declared with IRAM_ATTR,
* unless you pass the ESP_INTR_FLAG_IRAM flag when allocating the
* ISR in gpio_install_isr_service().
*
* This ISR handler will be called from an ISR. So there is a stack
* size limit (configurable as "ISR stack size" in menuconfig). This
* limit is smaller compared to a global GPIO interrupt handler due
* to the additional level of indirection.
*
* @param gpio_num GPIO number
* @param isr_handler ISR handler function for the corresponding GPIO number.
* @param args parameter for ISR handler.
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_STATE Wrong state, the ISR service has not been initialized.
* - ESP_ERR_INVALID_ARG Parameter error
*/
esp_err_t gpio_isr_handler_add(gpio_num_t gpio_num, gpio_isr_t isr_handler, void* args);
/**
* @brief Remove ISR handler for the corresponding GPIO pin.
*
* @param gpio_num GPIO number
*
* @return
* - ESP_OK Success
* - ESP_ERR_INVALID_STATE Wrong state, the ISR service has not been initialized.
* - ESP_ERR_INVALID_ARG Parameter error
*/
esp_err_t gpio_isr_handler_remove(gpio_num_t gpio_num);
#ifdef __cplusplus
}
#endif
#endif /* _DRIVER_GPIO_H_ */
Reference in New Issue View Git Blame Copy Permalink