// Copyright (C) 2023, Mark Qvist // This program is free software: you can redistribute it and/or modify // it under the terms of the GNU General Public License as published by // the Free Software Foundation, either version 3 of the License, or // (at your option) any later version. // This program is distributed in the hope that it will be useful, // but WITHOUT ANY WARRANTY; without even the implied warranty of // MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the // GNU General Public License for more details. // You should have received a copy of the GNU General Public License // along with this program. If not, see . #include "ROM.h" #include "Boards.h" #ifndef CONFIG_H #define CONFIG_H #define MAJ_VERS 0x01 #define MIN_VERS 0x49 #define MODE_HOST 0x11 #define MODE_TNC 0x12 #define CABLE_STATE_DISCONNECTED 0x00 #define CABLE_STATE_CONNECTED 0x01 uint8_t cable_state = CABLE_STATE_DISCONNECTED; #define MAX_INTERFACES 12 #define BT_STATE_NA 0xff #define BT_STATE_OFF 0x00 #define BT_STATE_ON 0x01 #define BT_STATE_PAIRING 0x02 #define BT_STATE_CONNECTED 0x03 uint8_t bt_state = BT_STATE_NA; uint32_t bt_ssp_pin = 0; bool bt_ready = false; bool bt_enabled = false; bool bt_allow_pairing = false; #define M_FRQ_S 27388122 #define M_FRQ_R 27388061 bool console_active = false; bool modems_installed = false; #define MTU 508 #define SINGLE_MTU 255 #define HEADER_L 1 #define MIN_L 1 #define CMD_L 64 #define eeprom_addr(a) (a+EEPROM_OFFSET) #define PA_OUTPUT_RFO_PIN 0 #define PA_OUTPUT_PA_BOOST_PIN 1 // MCU independent configuration parameters const long serial_baudrate = 115200; // SX1276 RSSI offset to get dBm value from // packet RSSI register const int rssi_offset = 157; // Default LoRa settings const int lora_rx_turnaround_ms = 66; const int lora_post_tx_yield_slots = 6; #define LORA_CAD_SYMBOLS 3 // Operational variables bool community_fw = true; bool hw_ready = false; bool disp_ready = false; bool pmu_ready = false; bool promisc = false; bool implicit = false; volatile bool packet_ready = false; uint8_t implicit_l = 0; uint8_t op_mode = MODE_HOST; uint8_t model = 0x00; uint8_t hwrev = 0x00; int last_rssi = -292; uint8_t last_rssi_raw = 0x00; uint8_t last_snr_raw = 0x80; uint8_t seq = 0xFF; uint16_t read_len = 0; bool serial_in_frame = false; FIFOBuffer packet_rdy_interfaces; uint8_t packet_rdy_interfaces_buf[MAX_INTERFACES]; // Incoming packet buffer uint8_t pbuf[MTU]; // KISS command buffer uint8_t cmdbuf[CMD_L]; // LoRa transmit buffer uint8_t tbuf[MTU]; uint32_t stat_rx = 0; uint32_t stat_tx = 0; unsigned long last_tx = 0; unsigned long last_rx = 0; // Power management #define BATTERY_STATE_DISCHARGING 0x01 #define BATTERY_STATE_CHARGING 0x02 #define BATTERY_STATE_CHARGED 0x03 bool battery_installed = false; bool battery_indeterminate = false; bool external_power = false; bool battery_ready = false; float battery_voltage = 0.0; float battery_percent = 0.0; uint8_t battery_state = 0x00; uint8_t display_intensity = 0xFF; uint8_t display_addr = 0xFF; bool display_diagnostics = true; bool device_init_done = false; bool eeprom_ok = false; bool firmware_update_mode = false; // Boot flags #define START_FROM_BOOTLOADER 0x01 #define START_FROM_POWERON 0x02 #define START_FROM_BROWNOUT 0x03 #define START_FROM_JTAG 0x04 // Subinterfaces // select interface 0 by default uint8_t interface = 0; RadioInterface* selected_radio; RadioInterface* interface_obj[INTERFACE_COUNT]; RadioInterface* interface_obj_sorted[INTERFACE_COUNT]; #if HAS_BUZZER // Buzzer bool buzzer_enabled = true; unsigned long last_tone_toggle = 0; uint16_t buzzer_delay = 0; uint16_t last_buzzer_tone = 0; #endif #endif