esp_timer_get_time returns monotonic time in microseconds, as a 64-bit
number. It can be called from tasks and interrupts, does not use any
critical sections/mutexes, and is thread safe.
The esp-idf expects duty values for the the sigma delta modulator in the range of -128 to 127
The arduino framework is supposed to use the range 0-255 thus the offset caclulation was wrong.
If you develop on windows and need cr/lf files, see this:
https://git-scm.com/book/en/v2/Customizing-Git-Git-Configuration#_formatting_and_whitespace
Git can handle this by auto-converting CRLF line endings into LF
when you add a file to the index, and vice versa when it checks out
code onto your filesystem. You can turn on this functionality with
the core.autocrlf setting. If you're on a Windows machine, set it
to true - this converts LF endings into CRLF when you check out code:
$ git config --global core.autocrlf true
This change uses the `_RST` bit of the i2c peripheral to force the hardware into power on reset state. The prior code assumed the peripheral was already in a reset, it just cleared the reset bit.
Chuck.
The cycle count that micros() is using to report timing is a PER Task value. When micros() or delayMicroseconds() is called from different Tasks, the lastCycleCount value may have no relationship to the current Task specific cycleCount. If the current cycleCount is less than the saved lastCycleCount a rollover condition is assumed. This erroneous conditions results in incorrect delays and reported microseconds. This fix creates thread local storage so that each Task will have accurate microsecond reporting and delays. The reported microseconds are not real time, they are microseconds of the current Task execution.
esp_efuse_mac_get_default() only stores into the bottom 6 bytes of it's 8-byte argument, so must initialize this arg to zero to avoid trash on the stack.
* Update mDNS and LEDC
* update toolchain
* Update IDF to 1c3dd23
* Advertise the board variant for Arduino OTA
* Add generic variant definition for mDNS
The existing code did not follow protocol with 10bit addressed devices. Per _Philps/NXP Semiconductors UM10204 I2C-bus specification and user manual Rev. 6 4April2014_ pg.15 3.1.11 10-bit addressing:
~The first seven bits of the first byte are the combination of 1111 0xx of which the last two bits (xx) are the two Most-Significant Bits (MSB) of the 10-bit address; the eighth bit of the first byte is the R/!W! bit the determines the direction of the message~
The i2cWrite() function was returning to the app before the i2c transaction had completed. This caused the next Wire() call to return a I2C_ERROR_BUSY.
Usable for library developers who write code not dependent on Arduino.
Adding 3 lines to the includes will permit their debug messages to be
visible in Arduino IDE or when enabled under IDF
Fix redefines of strXXX, original was using strnXXX with length set to 0x7fffffff. This caused problems with strcpy and strcat. The destination buffer was NULL'd to 0x7fffffff which killed the app.
* Addition of a i2cReset method and timeout handling for the case where the i2c hardware FSM (state machine) gets stuck in a busy state.
* Use newly added i2cReset function within the wire library.
* uartEnd: Unlock mutex before detaching rx and tx
This should solve the device freezing issue when Serial.end() is called
* Unlock UART MUTEX only for detaching Rx and Tx
* Thanks to @me-no-dev for pointing it out that
uart->dev->conf0.val can be inside mutex lock
It appears that the configurations for `ck_out_edge` were inverted for `SPI_MODE2` and `SPI_MODE3`. You can check the technical reference manual on page 76, table 23 "Clock Polarity and Phase, and Corresponding SPI Register Values for SPI Master".
I've check with my oscilloscope that the current configuration is wrong and this fix corrects the issue.
* Improvements in EspClass
- fixed not working functions for flash chip size, speed and mode
- added function to retrieve chip revision from eFuse
- flashRead / flashWrite supports encrypted flash
* Rename getCpuRevision function to getChipRevision
* Revert: flashRead / flashWrite supports encrypted flash
Reading and writing to encrypted flash has to be aligned to 16-bytes. Also NAND way of writing (i.e. flipping 1s to 0s) will not work with spi_flash_write_encrypted. Note: spi_flash_read_encrypted will always try to decrypt data, even if it wasn't encrypted in the first place.
WiFi and BlueTooth can now be started and stopped at will.
basic functions added to esp32-hal to start and stop the BT radio
SimpleBLE class added to show the most basic functionality
Example to show how to switch between BT, WiFi or Both
Previous __FlashStringHelper implementation was defines as a char which brought problem in case the method with char* parameter used overloading with __FlashStringHelper* parameter (they was identical). Now __FlashStringHelper is defined as a class and all casts between char* and __FlashStringHelper* are made with reinterpret_cast sugar.
example:
```cpp
//done once on WiFi init
configTime(-7200, 3600, "pool.ntp.org");
//get local time
struct tm timeinfo;
if(!getLocalTime(&timeinfo)){
Serial.println("Failed to obtain time");
return;
}
//print time
Serial.println(&timeinfo);
//print time with different format
Serial.println(&timeinfo, "%A, %B %d %Y %H:%M:%S");
```
fixes: https://github.com/espressif/arduino-esp32/issues/29
