* Add APB change callbacks and move cpu code to own file
* Properly set esp_timer and FreeRTOS tick dividers
* Improve updated devisors
* No need to update REF_TICK yet
* Add initial handling for UART baud change
* fix uartWriteBuf and uartDetectBaudrate
* trigger callbacks even when APB did not change
* toggle UART ISR on CPU change
* add XTAL freq getter and add cpu freq validation
* Support CPU frequency changes in I2C (#2287)
**esp32-hal-i2c.c**
* add callback for cpu frequency changes
* adjust fifo thresholds based on cpu frequency and i2c bus frequency
* reduce i2c bus frequency if differential is too small
**Wire.h**
* version to 1.1.0
* Implement clock change for the other peripherals
* remove bad CPU clock values from the menu
* Add note to CPU freqs that support WiFi and BT
The default SPI bus is VSPI (see libraries/SPI/src/SPI.cpp). This change corrects a misleading comment in a code example which was stating wrongly that HSPI would be the default one.
* Shows only free internal heap on logs
Since Mbedtls is running only on internal heap, show internal + PSRAM available memory on logs can confuse the users
* Clarify logs
* Fix error in PR #2048: if ::available() is called before ::connect() _rxBuffer is not initialised
* Fixed flash size check and added SPIFFS size check
* Rewriting ESP.getFreeSketchSpace(), moving code from HTTPUpdate.cpp
* Don't Return I2C_ERROR_CONTINUE on ReSTART
ReSTART operations on the ESP32 have to be handled differently than on AVR chips, so ReSTART operations(`Wire.endTransmission(false), Wire.requestFrom(id,size,false);` are queued until a STOP is send (`Wire.endTransmission(TRUE), Wire.endTransmission(), Wire.requestFrom(id,size), Wire.requestFrom(id,size,TRUE)). To indicate the queuing I had used `I2C_ERROR_CONTINUE`, this caused compatibility issues with the existing Arduino I2C Code base. So, back to Lying to the public(for their own good of course) about success! This update just returns `I2C_ERROR_OK` on ReSTART commands.
* add comments
add comments
* Change Return error for ReSTART operation to I2C_ERROR_OK
This change restores compatibility with pre-existing Arduino Libraries. The ReSTART queuing operations are hidden behind the scenes. Wire.endTransmission(id,len,FALSE); will know return I2C_ERROR_OK instead of I2C_ERROR_CONTINUE, Wire.lastError() will return the true condition of I2C_ERROR_CONTINUE.
* #1623, implementing suggested change
Splitted suggested fix issue #1623 in a header and source part. Dit not completely dive into the code.
Giving data twice as parameter feels wrong, but it compiles, and i can succesfully use the W5500 with SPI with this fix.
Doesn't compile without.
* #1623, implementing suggested change SPI.h/cpp
Splitted suggested fix issue #1623 in a header and source part. Dit not completely dive into the code.
Giving data twice as parameter feels wrong, but it compiles, and i can succesfully use the W5500 with SPI with this fix.
Doesn't compile without.
* Clean warnings when all warning enabled
Not used variables / functions due to debug log
Dual define with different values :
cores\esp32/binary.h
#define B110 6
#define B1000000 64
tools/sdk/include/newlib/sys/termios.h
#define B110 3
#define B1000000 23
Local variable returned in WiFiclient Secure
* change due to deprecated function
* Update with proper variable and label
* Update esp32-hal-i2c.c
* Apply changes requested
* Fix warnings due to #define conflict thanks @atanisoft
This allow to catch the events when connected /disconnected,, etc...
This also allow to get parameters of events like the remote address of connected devices, etc...
Small change but lot of flexibility
* Added HTTPUpdate class for downloading sketches from a server
* Added HTTPUpdate class for downloading sketches from a server
* Added HTTPUpdate to CMakeLists.txt
* Change ESP8266 class references to ESP32 for httpUpdate.ino example
* Change ESP8266 class references to ESP32 for httpUpdate.ino example. setLedPin() commented out because not all boards support LED_BUITLIN
* Added check to handle mixup of old and present api properly
* Correct HTTPClient::setTimeout() to convert milliseconds to seconds. Correct WiFiClient::setTimeout() to call Stream::setTimeout() with seconds converted back to milliseconds. Remove inproper checks for _insecure.
* Added small comment because it looked like the Travis build did not finish
* Pass client parameter into two new begin() functions. Set other begin() functions deprecated. Updated library version to 1.2
* Added working HTTPS example on a public url with a certificate
* Remove two unnecessary tests in ::disconnect()
* Add a scoping block to BasicHttpsClient.ino to assure HTTPClient is destroyed before WiFiClientSecure
* Added check to handle mixup of old and present api properly
* Correct HTTPClient::setTimeout() to convert milliseconds to seconds. Correct WiFiClient::setTimeout() to call Stream::setTimeout() with seconds converted back to milliseconds. Remove inproper checks for _insecure.
* Added small comment because it looked like the Travis build did not finish
* removed uint8_t Wire.endTransmission(uint8_t sendStop)
Having both endTransmission(bool) and endTransmission(uint8_t) creates problems.
There is no need for endTransmission(uint8_t)
endTransmission(1) and endTransmission(0) works with endTransmission(bool).
Removing endTransmission(uint8_t) allows the ESP32 code to be compatible with
all the other Arduino cores by allowing endTransmission(1) and endTranmission(0)
to work as it does on all the other cores.
* Wire library version bump for endTransmission() update
* TX Flow Control and Code cleanup
* Use semaphore instead of delay
TX functionality is done.
* Use single buffer and empty queue on exit
* Fix compile issues because of LwIP code relocation
* Add temporary header to fix Azure not compiling
* Fix AsyncUDP early init
* AsyncUDP Multicast fixes
* Add source mac address and rework multicast
* Allow redefinition of default pins for Serials 1 and 2
* Update IDF to 3276a13
* Update esptool.py to 2.5.0
* Fix sketches
* Fix log level in BluetoothSetial
* rmt driver initial version
* supporting conti mode plus interrupts
* using conitnous mode for sending more data
* working continous mode
* rmt driver cleanup after conti mode
* initial version of rmt driver
* adding a simple example
* adding channel and block locks
* modified of rmt interface for simpler/easier usage
* adding header sentinels, split interface to common and additional settings
* Fixes per code review + support for rx callback mode
* renamed internal structures and enums, fixed formatting
* cmake support for rmt
* refactored tx-conti interrupts to function to make it more readable
* added Tx and Rx examples
* added license headers
* minor updates per review
* used struct access, renamed defines, corrected diagram
* First commit of FFat library
* Fixed reboot loops if no fat present. Added CMakeLists
* Functionalize the partition checks
* Cleanup, especially in format
* Dont format if mounted. More wording cleanup
* 16M ffat should only be on 16M board
* Fix some casting issues that trip up the compiler when building as ESP-IDF component
Few testers let me know, they were unable with connection to Eduroam network under PEAP+MsCHAPv2 methods.
They were trying many modifications. Solution is very absurd.
Change board to STA mode manually.
One tester from Italy was able to connect to Eduroam network under TTLS + MsCHAPv2 with that sketch too!
Sketch was tested and worked almost for all testers with that problem.
* ReSTART fix, Sequencing fix
pr #1665 introduce a problem with ReSTART, when solving this problem I found an interaction between the TxFifo refill, RxFifo empty and CMD[] fill. during certain sequences a dataqueue command would be skipped, this skipping resulted in a mismatch between the contents of the TxFifo and the i2c command sequence. The problem manifested as an ACK error.
In addition to this required bug fix I propose:
* `Wire.begin()` be changed from a `void` to a `bool` this will allow the reset functionality of `Wire.begin()` to be reported. Currently `Wire.begin()` attempts to reset the i2c Peripheral, but cannot report success/failure.
* `Wire.busy()` be added. this `bool` function returns the hardware status of the bus. This status can be use in multi-master environments for application level interleaving of commands, also in single master environment, it can be used to detect a 'hung' bus. With the functional change to `Wire.begin()` this allows app level recover of a hung bus.
* `Wire.lastError()` value updated for all errors, previously when interleaving `Wire.endTransmission(false)` and `Wire.readTransmission(false)`, the 128 byte `Wire.write()` buffer was exhausted without generating and error(very exotic). I discovered this error when I created a sequence of directed reads to a EEPROM. Each directed read used 2 bytes of the 128 byte `write()` buffer, so after 64 consecutive ReSTART writes with ReSTART reads, `Wire()` had no room to record the directed address bytes. It generated just a NAK check without setting the EEPROMs internal register address. The succeeding ReSTART read succeeded at incorrect address.
* Changes to the HAL layer:
** added `i2cGetStatus()` which returns the i2c peripheral status word, used to detect bus_busy currently
** added `i2cDebug()` programmatic control of debug buffer output
** changed `i2cAddQueue()` to allow data_only queue element this will allow a i2c transaction to use multiple data pointers.
** removed direct access to DumpInts(), DumpI2c() from app, use i2cDebug() to set trigger points
*
* Update esp32-hal-i2c.c
* Update Wire.cpp
* ReSTART, Sequencing
pr #1665 introduce a problem with ReSTART, when solving this problem I found an interaction between the TxFifo refill, RxFifo empty and CMD[] fill. during certain sequences a dataqueue command would be skipped, this skipping resulted in a mismatch between the contents of the TxFifo and the i2c command sequence. The problem manifested as an ACK error.
In addition to this required bug fix I propose:
* `Wire.begin()` be changed from a `void` to a `bool` this will allow the reset functionality of `Wire.begin()` to be reported. Currently `Wire.begin()` attempts to reset the i2c Peripheral, but cannot report success/failure.
* `Wire.busy()` be added. this `bool` function returns the hardware status of the bus. This status can be use in multi-master environments for application level interleaving of commands, also in single master environment, it can be used to detect a 'hung' bus. With the functional change to `Wire.begin()` this allows app level recover of a hung bus.
* `Wire.lastError()` value updated for all errors, previously when interleaving `Wire.endTransmission(false)` and `Wire.readTransmission(false)`, the 128 byte `Wire.write()` buffer was exhausted without generating and error(very exotic). I discovered this error when I created a sequence of directed reads to a EEPROM. Each directed read used 2 bytes of the 128 byte `write()` buffer, so after 64 consecutive ReSTART writes with ReSTART reads, `Wire()` had no room to record the directed address bytes. It generated just a NAK check without setting the EEPROMs internal register address. The succeeding ReSTART read succeeded at incorrect address.
* Changes to the HAL layer:
** added `i2cGetStatus()` which returns the i2c peripheral status word, used to detect bus_busy currently
** added `i2cDebug()` programmatic control of debug buffer output
** changed `i2cAddQueue()` to allow data_only queue element this will allow a i2c transaction to use multiple data pointers.
** removed direct access to DumpInts(), DumpI2c() from app, use i2cDebug() to set trigger points
*
* Forgot DebugFlags Return
@andriyadi found this, total brain fade on my part.
If you receive a package with a data length of zero, parsePacket returns 0, but rx_buffer will exist. So if another parsePacket with no read access returns to zeros, there is still data that can be read. This example would not work: https://www.arduino.cc/en/Reference/EthernetUDPParsePacket
Also I added a check if rx_buffer exit when you try to flush it.
EEPROM.h uses data types which are declared through Arduino.h but that file does not contain an #include directive for Arduino.h. This does not cause any problems when the EEPROM library is #included from a .ino file because the Arduino IDE automatically adds an #include directive for Arduino.h but this is not the case for .cpp files. If a .cpp file has an #include directive for EEPROM.h that does not follow an #include directive for Arduino.h then compilation fails:
E:\arduino\hardware\espressif\esp32\libraries\EEPROM/EEPROM.h:91:5: error: 'float_t' does not name a type
float_t readFloat(int address);
^
E:\arduino\hardware\espressif\esp32\libraries\EEPROM/EEPROM.h:92:5: error: 'double_t' does not name a type
double_t readDouble(int address);
^
E:\arduino\hardware\espressif\esp32\libraries\EEPROM/EEPROM.h:95:5: error: 'String' does not name a type
String readString(int address);
^
E:\arduino\hardware\espressif\esp32\libraries\EEPROM/EEPROM.h:110:36: error: 'float_t' has not been declared
size_t writeFloat(int address, float_t value);
^
E:\arduino\hardware\espressif\esp32\libraries\EEPROM/EEPROM.h:111:37: error: 'double_t' has not been declared
size_t writeDouble(int address, double_t value);
^
E:\arduino\hardware\espressif\esp32\libraries\EEPROM/EEPROM.h:114:37: error: 'String' has not been declared
size_t writeString(int address, String value);
* Allow using argument with attachInterrupt
* formatting
replace tabs with spaces
* fix bug more then 1 interrupt
* leftover
* add example
* make attachInterruptArg public
* update example
* leftover
* fix sdmmc config
* Fix warnings in EEPROM
from @Curclamas
* remove leftover TAG in EEPROM
* Initial add of @stickbreaker i2c
* Add log_n
* fix warnings when log is off
* i2c code clean up and reorganization
* add flags to interrupt allocator
* fix sdmmc config
* Fix warnings in EEPROM
from @Curclamas
* remove leftover TAG in EEPROM
* fix errors with latest IDF
* fix debug optimization (#1365)
incorrect optimization for debugging tick markers.
* Fix some missing BT header
* Change BTSerial log calls
* Update BLE lib
* Arduino-ESP32 release management scripted (#1515)
* Calculate an absolute path for a custom partitions table (#1452)
* * Arduino-ESP32 release management scripted
(ready-to-merge)
* * secure env for espressif/arduino-esp32
* * build tests enabled
* gitter webhook enabled
* * gitter room link fixed
* better comment
* * filepaths fixed
* BT Serial adjustments
* * don't run sketch builds & tests for tagged builds
* Return false from WiFi.hostByName() if hostname is not resolved
* Free BT Memory when BT is not used
* WIFI_MODE_NULL is not supported anymore
* Select some key examples to build with PlatformIO to save some time
* Update BLE lib
* Fixed BLE lib
* Major WiFi overhaul
- auto reconnect on connection loss now works
- moved to event groups
- some code clean up and procedure optimizations
- new methods to get a more elaborate system ststus
* Add cmake tests to travis
* Add initial AsyncUDP
* Add NetBIOS lib and fix CMake includes
* Add Initial WebServer
* Fix WebServer and examples
* travis not quiting on build fail
* Try different travis build
* Update IDF to aaf1239
* Fix WPS Example
* fix script permission and add some fail tests to sketch builder
* Add missing space in WiFiClient::write(Stream &stream)
