This version no longer needs an interrupt for each byte transferred. It only needs interrupts for START, STOP, FIFO empty/Full or error conditions. This dramatically reduces the interrupt overhead. I think the prior version was causing an interrupt overload condition where the ISR was not able to process every interrupt as they happened.
the 'eject' ERROR is and indication of an interrupt triggering without an source. I am working to eliminate these serviceable interrupt. This update increase stability on a HelTek Wifi Lora 32 board. with a SSD1306 OLED. This update fixes a glaring error in the interrupt allocation code, the Interrupt mask was wrong. I also dynamically adjust the FiFo thresholds based on Bus clockrate. The change to FiFo thresholds has reduced the number for 'eject' events. I also change 'eject' from and ERROR to DEBUG. An 'eject' event does not compromise i2c transmissions. It happens after a transaction has completed.
Chuck.
If Core Debug Level is at DEBUG, a confusing debug message will be emitted if the I2C transaction takes longer complete than the calculated minimum time. This original debug message was just to prove that this new i2c code could correctly handle SCL stretching or interrupt latency issues. This delay is not a problem, or an error. Usually it is caused by a higher priory interrupt starving the i2c ISR. Usually WiFi is the culprit. As long of this delay is within the configured timeout (by default 50ms, or can be set with Wire.setTimeOut(milliseconds);) no problem will occur and the transaction will successfully complete.
Chuck.
* fix sdmmc config
* Fix warnings in EEPROM
from @Curclamas
* remove leftover TAG in EEPROM
* Initial add of @stickbreaker i2c
* Add log_n
* fix warnings when log is off
* i2c code clean up and reorganization
* add flags to interrupt allocator
* fix sdmmc config
* Fix warnings in EEPROM
from @Curclamas
* remove leftover TAG in EEPROM
* fix errors with latest IDF
* fix debug optimization (#1365)
incorrect optimization for debugging tick markers.
* Fix some missing BT header
* Change BTSerial log calls
* Update BLE lib
* Arduino-ESP32 release management scripted (#1515)
* Calculate an absolute path for a custom partitions table (#1452)
* * Arduino-ESP32 release management scripted
(ready-to-merge)
* * secure env for espressif/arduino-esp32
* * build tests enabled
* gitter webhook enabled
* * gitter room link fixed
* better comment
* * filepaths fixed
* BT Serial adjustments
* * don't run sketch builds & tests for tagged builds
* Return false from WiFi.hostByName() if hostname is not resolved
* Free BT Memory when BT is not used
* WIFI_MODE_NULL is not supported anymore
* Select some key examples to build with PlatformIO to save some time
* Update BLE lib
* Fixed BLE lib
* Major WiFi overhaul
- auto reconnect on connection loss now works
- moved to event groups
- some code clean up and procedure optimizations
- new methods to get a more elaborate system ststus
* Add cmake tests to travis
* Add initial AsyncUDP
* Add NetBIOS lib and fix CMake includes
* Add Initial WebServer
* Fix WebServer and examples
* travis not quiting on build fail
* Try different travis build
* Update IDF to aaf1239
* Fix WPS Example
* fix script permission and add some fail tests to sketch builder
* Add missing space in WiFiClient::write(Stream &stream)
This change uses the `_RST` bit of the i2c peripheral to force the hardware into power on reset state. The prior code assumed the peripheral was already in a reset, it just cleared the reset bit.
Chuck.
The existing code did not follow protocol with 10bit addressed devices. Per _Philps/NXP Semiconductors UM10204 I2C-bus specification and user manual Rev. 6 4April2014_ pg.15 3.1.11 10-bit addressing:
~The first seven bits of the first byte are the combination of 1111 0xx of which the last two bits (xx) are the two Most-Significant Bits (MSB) of the 10-bit address; the eighth bit of the first byte is the R/!W! bit the determines the direction of the message~
The i2cWrite() function was returning to the app before the i2c transaction had completed. This caused the next Wire() call to return a I2C_ERROR_BUSY.
* Addition of a i2cReset method and timeout handling for the case where the i2c hardware FSM (state machine) gets stuck in a busy state.
* Use newly added i2cReset function within the wire library.
IDF Options:
- Autostart Arduino (implements app_main)
- Disable HAL locks
- Set HAL debug level
- Auto-connect STA if configured (else will connect after WiFi.begin())
